beautypg.com

Studio Technologies 68A 2001 User Manual

Page 11

background image

Model 68A/69A User Guide

Issue 1, March 2001

Studio Technologies, Inc.

Page 11

for Surround

cable harnesses, each with a 25-pin D-sub
plug (male) on one end and the desired
connectors on the other end, are neces-
sary. These cable harnesses are not
supplied by Studio Technologies. Note
that our friends in some locations may
use the term “loom” instead of harness.

The wiring scheme used by the D-subs
comply with that made familiar by
TASCAM® with their DA-88® product.
Wiring harnesses prepared for connecting
to the surround and stereo inputs are
identical to DA-88-style input harnesses.
A wiring harness prepared for the monitor
outputs is identical to that of a DA-88-style
output harness. Please refer to Figures 4,
5, and 6 for the exact connection details.
Note that the Model 68A’s D-sub connec-
tors use 4-40 threads.

Unless there’s a special need, it may be
cost and time effective for you to purchase
commercially made cable harnesses. Let
the large market for DA-88-style cabling
help you painlessly install your system!

Surround and Stereo Inputs

The connectors labeled Input 1–Surround
A & Input 3–Stereo A and Input 2–Sur-
round B & Input 4–Stereo B are used to
interface with the input circuits. Please
refer to Figures 4 and 5 for details on the
exact “pin out” of the D-sub connectors.
Each input circuit is electronically bal-
anced, and is intended for connection to
balanced or unbalanced sources with
nominal signal levels of –12dBV to +6dBu.
A 15-turn trim potentiometer is associated
with each input, allowing the input sensitiv-
ity to be adjusted to match the source’s
level. The configuration section of this
guide provides details on using the trim
pots.

Signal

Signal

Connections

High (+)

Low (–)

Shield

SURROUND A-L

24

12

25

SURROUND A-C

10

23

11

SURROUND A-R

21

9

22

SURROUND A-LS

7

20

8

SURROUND A-RS

18

6

19

SURROUND A-LFE

4

17

5

STEREO A-L

15

3

16

STEREO A-R

1

14

2

Notes: 1) Connector type on Model 68A is 25-pin D-subminiature

female. Installer must provide plug (male). Connector
uses 4-40 threaded inserts for locking with mating plug.

2) Wiring scheme follows TASCAM DA-88 convention.
Standard DA-88-type wiring harnesses are directly
compatible, with the exception of 4-40 screw threads
being required.

Figure 4. Connections for Inputs Surround A
and Stereo A

Signal

Signal

Connections

High (+)

Low (–)

Shield

SURROUND B-L

24

12

25

SURROUND B-C

10

23

11

SURROUND B-R

21

9

22

SURROUND B-LS

7

20

8

SURROUND B-RS

18

6

19

SURROUND B-LFE

4

17

5

STEREO B-L

15

3

16

STEREO B-R

1

14

2

Notes: 1) Connector type on Model 68A is 25-pin D-subminiature

female. Installer must provide plug (male). Connector
uses 4-40 threaded inserts for locking with mating plug.

2) Wiring scheme follows TASCAM DA-88 convention.
Standard DA-88-type wiring harnesses are directly
compatible, with the exception of 4-40 screw threads
being required.

Figure 5. Connections for Inputs Surround B
and Stereo B

This manual is related to the following products: