Fp_led_rev040210 (4), Fp series, Fp-light | light settings and controls – Soundtube FP6020-II User Manual
Page 4

FP-Light | Light Settings and Controls
Module Description
The LED light can operate as a
standard light fixture or can be
triggered with the FP-Motion
module. Brightness can be
controlled either internally with
an adjustment on the FP-Light
module or externally with a
global system controller. To
trigger the FP-Light with the
FP-Motion, refer to Section 3
and the FP-Motion installation
instructions.
Section 1 – Wiring The
Speaker
Connecting The External
Power Supply
The FP-Light requires an
external power supply rated
between 12 V and 18 V
(optional SoundTube
accessories: AC-PS-1530 and
AC-PS-1550). Connect the
power supply to the
brown/white (+) and brown (-)
wires in the Cat 5 cable.
Section 2 – Adjusting the
Brightness
Remove The Pod Cover
Remove the pod cover [1] from
the FP pod [2] by loosening the
two captured screws [3] on
each side (Figure 1). The
screws will not come out of the
cover.
Adjust The Brightness
Internally
To manually adjust the
brightness of the light use a
small screwdriver to turn the
trim pot on the upper right
corner of the light module [6].
Turning the trim pot clockwise
will increase brightness and
counterclockwise will decrease
brightness.
Adjust The Brightness
Externally
The external brightness control
is disabled by factory default.
To enable the external
brightness control, move
Jumper 4 [4] on the upper left
corner of the FP Light module
to the enabled position over
the two right pins (Figure 2).
To adjust the brightness
externally, incorporate a
controller such as Crestron or
Lutron and connect the
positive lead [+] from the
controller to the orange/white
wire in the Cat 5, and the
negative lead [–] from the
controller to the orange wire in
the Cat 5. The Light module
accepts 0 V to 10 V DC signal
to control the brightness. To
achieve maximum
brightness, the trim pot
must be turned fully
clockwise (see previous
step).
Section 3 – Motion Sensor
Triggering
Enable The Motion Sensor
Note: To use with motion
triggering, both the FP-Light
and the FP-Motion modules
must be installed.
Since motion sensing is
disabled by factory default, the
light will be on continuously
when power is supplied. To
enable motion sensor
triggering of the light, move
Jumper 2 [5] on the lower left
corner of the FP-Light module
to the two left pins (Figure 3).
When this feature is enabled,
the light will only activate when
motion is detected. See
FP-Motion sensor instructions
for settings and controls.
Section 4 – Replacing The
Pod Cover
Replace pod cover [1] and
tighten screws [3].
Power
External Controller
LED Light
Amp Control
Speaker
Contact closure = Green/White
Contact closure = Green
12 V trigger = Blue/White
Amp control = Blue
LED control = Orange/White
LED control = Orange
Amp gain = Blue
Amp gain = Orange
Left in = White
Left in = Green
Right in = Red
Right in = Black
Power = Brown/White
Power ground = Brown
Cat 5 Wiring
All signal and control wires are located in the signal/hanging cable provided
with the FP unit speaker wires. A Cat 5 cable (blue shield) contains the control and power
wires; audio wires are individual 16-gauge wires in the bundle.
Wiring Instructions
1 FP-Light module
2 Jumpers
Contents
Figure 2
Figure 3
FP pod [2]
Brightness control [6]
Pod cover [1]
Light module
Main electrical board
LED lamp baffle
(ships with light module only)
FP modules ship pre-installed
from the factory.
Other FP Series optional
modules include:
1. FP-Motion
2. FP-ScentAir
3. FP-Amp
All modules require a power source.
An optional 15-volt source is
available from SoundTube
(Model numbers: AC-PS-1530
or AC-PS-1550).
Jumper 4 (J4) external
brightness control [4]
Light connection
Jumper 2 (J2) motion
sensor control [5]
Pod cover screws [3]
Figure 1
FP Series
Do not spec or install speaker near support beam, ventilation duct or
other structure that may interfere with speaker function or dispersion.
Warning
© 2010 SoundTube Entertainment, Inc. All rights reserved. PN INS-FP-LIGHT Rev04.02.10
Warning
SoundTube speakers must be installed by a professional audio installer/contractor. For safety and for
optimum audio performance, installer must follow all directions issued by SoundTube Entertainment.
1.435.647.9555
|
800.647.TUBE
|
www.soundtube.com
435.647.9555
|
800.647.TUBE
|
www.soundtube.com
Install Instructions For:
FP-Light
FP Series
435.647.9555
|
800.647.TUBE
|
www.soundtube.com
Install Instructions For:
FP-Light
FP Series