Denon AVP-A1HDCI - Manual (Page 7)

7
GUI Menu Map
Pla
ybac
k
Inf
or
mation
Tr
oubleshooting
Setup
Parameter
Audio
Adjust various audio parameters.
F Menu tree F
Parameter
Audio
a Surround Parameters
s Audyssey Settings
a Surround Parameters
Adjust surround sound parameters.
The adjustable parameters differ for the different surround
modes.
NON MTRX MTRX ON PLIIx CINEMA z 1 PLIIx MUSIC z 2
ES MTRX z 3 ES DSCRT z 4 DSCRT ON OFF
z 1: This can be selected when “Surround Back” is set to “2spkrs”
at the GUI menu “Manual Setup” – “Speaker Setup” – “Speaker
Confi guration” setting.
z 2: This can be selected when “Surround Back” is set to “2spkrs”
or “1spkr” at the GUI menu “Manual Setup” – “Speaker Setup”
–“Speaker Confi guration” setting.
z 3: This can be selected when playing DTS sources.
z 4: This can be selected when playing DTS sources including a
discrete 6.1-channel signal identifi cation signal.
SB CH Out (for Multi-channel sources )
Select playback mode for surround back channels.
[Selectable items]
When using the surround back speaker, you can change the “SB
CH Out” setting by pressing
STANDARD .
s Audyssey Settings
Select Room EQ, Dynamic EQ and Dynamic Volume.
Room EQ
[Selectable items]
Audyssey
: Optimize frequency response of all speakers.
Audyssey Byp. L/R
: Optimize frequency response of speakers
except front L and R speakers.
Audyssey Flat
: Optimize frequency response of all speakers
to fl at response.
Manual
: Apply frequency response set with “Manual
EQ”.
OFF
: Turn equalizer off.
Operating from the main unit or main remote
control unit
Press ROOM EQ .
Audyssey Audyssey Byp. L/R
Audyssey Flat Manual
OFF
• When “Audyssey”, “Audyssey Byp. L/R” or “Audyssey Flat” is
selected, “ ” lights.
• After running Auto Setup, if the Speaker Confi guration, Distance,
Channel Level, and Crossover Frequency have changed without
increasing the number of speakers measured, only “
”
lights.
• “Audyssey”, “Audyssey Byp. L/R” and “Audyssey Flat” can be
selected after the auto setup procedure has been performed.
• After performing “Auto Setup”, the “Room EQ” setting automatically
becomes “Audyssey”.
• If the settings of speakers for which “None” has been determined
at “Auto Setup” are changed, “Audyssey”, “Audyssey Byp. L/R”
and “Audyssey Flat” cannot be selected. Either perform Auto Setup
again, or return to the setting after running Auto Setup with “Auto
Setup” – “Parameter Check” – “Restore”.
• When using headphones or analog EXT. IN mode, “Room EQ”
cannot used.
Assign None
SIRIUS
Assign SIRIUS to this source.
[Input source] CD DVD HDP TV/CBL SAT VCR
DVR-1 DVR-2 V.AUX
[Selectable items]
NOTE
• “SIRIUS” and “iPod Dock” cannot both be assigned.
• When “SIRIUS” is assigned to the input source, connect to port 2
of the RS-232C connector. In this case, you can not use port 2 of the
RS-232C connector as an external controller.
• The “HDMI” and “Component” cannot be set for input sources for
which “SIRIUS“ is assigned.
Digital
Select digital input connector to assign to this source.
[Input source] CD DVD HDP TV/CBL SAT VCR
DVR-1 DVR-2 V.AUX
(
SIRIUS
)
[Selectable items] Coaxial1 ~ 4 Optical1 ~ 5
DENON LINK z BNC1/2 None
z : When a DENON DVD player and the DENON LINK have been
connected, be sure to make a setting to “DENON LINK”.
NOTE
This cannot be set for input sources for which “iPod dock” is
assigned.
Input
source
CD DVD HDP TV/CBL SAT VCR DVR-1 DVR-2 V.AUX
Default
setting Coaxial
4
Coaxial
1
Coaxial
2
Optical
1
Coaxial
3
Optical
4
Optical
2
Optical
3
Optical
5
g Assign
Assign input sources to input connectors.
1.AVP-A1HDCI_AVR5308CI_2nd.indd 7 2008/09/03 9:22:46