REMKO VRS 20 INOX - Manual (Page 4)

4
The units are designed for exclusive use with 1-speed
fan/burner operation.
The units are operated with a separate forced-air oil
burner.
It is essential to connect the units to an exhaust system
approved by the state building authorities.
The units are equipped with a 1-speed radial fan with
drive motor that runs quietly and requires little mainte-
nance as well as attached switching and regulating units.
The units meet the basic safety and health require-
ments found in the relevant EU regulations. They are
safe and easy to operate.
The robust design and clean processing of these high-
quality units ensure a long service life and smooth op-
eration. They can also be assembled quickly, easily and
affordably and are easy to service.
Safety Instructions
Make sure to observe relevant local building and fire
protection codes and abide by professional association
regulations when the units are in operation!
◊ Before performing any maintenance or repair work,
make sure to unplug the units from the power supply!
Remove fuses or switch off the customer-supplied
main switch.
*
It is not sufficient to switch off the units with the
operating switch!
◊ The units may only be operated by persons who
have received proper training in their operation.
◊ The units must be installed and operated in such a
way that people are not exposed to radiant heat and
fires cannot occur.
◊ The units may only be installed and operated in
closed rooms where the units have adequate air
supply for combustion.
If this cannot be guaranteed, a separate burner-
driven device that sucks in fresh air from the outside
must be installed.
◊ The units may only be set up on a non-flammable
surface.
◊ The units may only be attached to non-flammable,
sturdy structures or ceilings made from the materials
with sufficient load-bearing capacity.
◊ The units are to be attached with sturdy mounts
which are fixed on the unit.
◊ The units may not be set up or operated in surround-
ings susceptible to fire or explosions.
◊ The units must be set up outside of traffic zones,
e.g. away from cranes.
◊ A safety zone of 1 m is to be maintained around the
units.
◊ The protective air suction grille must always be kept
free of dirt and loose objects.
◊ Never insert foreign objects into the units.
◊ Do not expose the units to a direct stream of water.
◊ Never let water get inside the units.
◊ All of the units’ electrical cords are to be protected
from damage (e.g. caused by animals, etc.).
◊ Do not bypass or block safety mechanisms while
the unit is in operation.
REMKO automatic heaters supply heat or regulate the
temperature of:
◊ Workshops
◊ Warehouses
◊ Exhibition spaces
◊ Trade show spaces
◊ Temporary structures for warehousing
◊ Showrooms
◊ Greenhouses etc.
Operating Locations of the Units
The units are direct-fired devices that supply instanta-
neous heat. They are only used for industrial and com-
mercial purposes. There are generally no restrictions as
to where they can be used.
Proper Use
The units have been designed and equipped exclu-
sively for industrial and commercial heating and ventila-
tion purposes.
The manufacturer assumes no liability for damage re-
sulting from non-compliance with manufacturer specifi-
cations and legal requirements, or if modifications are
made to the units.
Description of the Unit
The units (automatic heaters) have been designed for
universal, fully-automatic and smooth operation. They
are fired directly with heating oil or diesel.
Operation
After switching on the unit by setting the operating
switch to “Heizen” (heating), the forced-air burner turns
on automatically.
he green “burner“ operating light is illuminated on the
control panel for monitoring purposes. The combustion
chamber with heat-exchanger now heats up until the
target temperature is reached.
After the burner has run for a short time, the temperature
control thermostat “TR” (rated temperature 35 to 40 °C)
automatically switches the air supply fan on. Warm air
is blown out.
The combustion chamber with heat-exchanger is
heated up until the target temperature of the tempera-
ture monitor (TW) is reached.