Profax PRO II x - Manual (Page 9)

1. Remove hinged cover.
2. Locate TS2 terminal strip.
3. Remove the two jumper links from TS2.
4. Install the 115/24 VAC transformer (St./No. 9045) onto it's mounting holes using the supplied four 8/32 screws, washers,
lockwashers and nuts.
5. Cut the transformer wires back so as to neatly reach their respective TS2 terminal listed in step 6.
6. Install the supplied spade wire terminals to the transformer wires.
7. Connect the transformer wires to terminal strip TS2 as follows:
White to Terminal 1
Yellow to Terminal 2
Yellow to Terminal 3
Black to Terminal 4
8. Install the hinged cover making sure not to trap and or pinch any wiring.
® ®
® ®
7 6
Installation Installation
1. Wire Speed Control
2. Power Switch and Power "ON" Light
3. Euro-Quick Adapter
CONTROL PANEL
THREADING WELDING WIRE AND ADJUSTING TENSION
OPTIONAL 115/24 VAC TRANSFORMER INSTALLATION
TS1 CONTACTOR TERMINAL STRIP OPERATION
SPOOL BRAKE ADJUSTMENT
1. Release pressure arm(s) by sliding the tension 5. Holding the mig gun out straight, feed the welding wire
adjustment lever(s)down. through the mig gun by using the gun trigger.
2. Route the welding wire through the inlet guide 6. Reinstall the contact tip.
across the drive roll(s) and into the outlet guide. 7. To adjust drive roll pressure - hold the mig gun no less
Slide at least six inches of wire into the outlet guide. than four inches up from a wood surface. Press the
3. Close pressure arm(s) and secure by sliding the gun trigger to feed wire and tighten the wire tension adjust
tension adjustment lever(s) up until locked in place. ment knob to the point where the wire does not slip.
4. Remove the mig gun contact tip. 8. Cut off wire and close cover.
NOTE: Too much wire tension will damage motor, cause erratic feeding and excessively wear drive rolls
1. Tension should be adjusted with wire spool on feeder.
2. Remove wire spool securing nut.
3. Turn the tension adjustment nut to the right to increase braking tension.
4. Adjust until a slight force is felt as you turn the spool by hand.
5. Install wire spool securing nut.
NOTE: Too much brake tension will cause erratic feeding.
WOOD
TIGHTEN
SPOOL
SECURING NUT
TIGHTEN
TENSION
NUT
SPINDLE
ASSY.
3
1
2
TS2 SET FOR
115 VAC OPERATION
TS2 SET FOR
24 VAC OPERATION
JUMPER
LINKS
YELLOW
YELLOW
WHITE
BLACK
CONTACT CLOSURE OPERATION
This setting is for welding power sources that require a normally open set of
contacts to operate the contactor. When the normally open set of contacts on K1
relay close it completes the circuit and energizes the contactor. Pins F and E on RC1
will give contact closure operation by the wire feeder when the TS1 jumper is from
terminal 1 to 2.
VOLTAGE FEEDBACK CONTACTOR OPERATION
This setting is for power sources that require voltage feedback to operate the
contactor. When K1 relay closes voltage will be sent back to the welding power
source to energize the contactor. This setting is normally used with the 115/24 VAC
transformer option (St./No. 9045) to send 115 VAC back to the welding power
source to operate the contactor circuit. Pins F and B on RC1 will give voltage
feedback operation by the wire feeder when the TS1 jumper is from terminal 2 to 3.
1 2 3
CONTACT
CLOSURE
VOLTAGE
FEEDBACK
1
CONTACT
CLOSURE
2 3
VOLTAGE
FEEDBACK
CAUTION!
Jumper links on TS2 must be removed when
installing the 9045 115V transformer option.
Failure to remove links will cause the pc board
to fail and void warranty.