Osburn AC02582 - Manual (Page 2)

INSTRUCTIONS FOR USE
IMPORTANT NOTES:
* Each use, verify that HEPA filter is in place and that HEPA seal plate
wing nut is tight. Always test seal by vacuuming up a small amount of
ash while located away from living areas
** Do not attempt to use vac to remove large piles of ash from a fireplace
or wood stove. Instead remove bulk of ash with a shovel and ash can
(or hod) and then use the ash vac for final cleanup.
1. Plug cord into outlet, (see photo 1 bellow).
2. Press the on/off button to switch the appliance on (see photo
2 bellow).
3. For fireplaces and wood burning stoves see “important
note **”, above. Place nozzle in firebox. Keep nozzle pressed
against the flat surfaces of stove or fireplace to limit entrance
of large chunks into pickup tube. Use the built-in vibrating
filter cleaning feature after approximately each 1 cup of ash
is removed or when suction is reduced. Shaker instructions
are below. If large chunks are picked up, turn off machine to
dislodge.
HOW TO USE THE BUILT-IN VIBRATING FILTER CLEANING
FEATURE
When the suction is reduced or after about 1 cup of ash has been
removed use the vibration knob to help remove ash from filter
without taking off the lid.
A. Turn off machine!
B. Hold can down and retract shake off knob fully.
C. Release so knob bangs top lid.
D. This will send vibrations through the top lid to the filter to
help clear debris. Repeat 5 to 10 times. Suction should now
improve at star-tup.
4. When finished cleaning turn switch off, photo (see photo 4
following) .
5. Remove the plug from the outlet (see 5 following) and take
vacuum to an outside location away from valuables and
breezes.
SPECIAL NOTES - IMPORTANT!
• Check your ash vacuum before turning it on. Keep cover
latches in place and in working order. Replace damaged,
missing or failed parts before using it.
• Ensure that anyone who uses the ash vacuum is familiar with
all safety precautions.
• Filter should be removed and thoroughly cleaned monthly or
after each 3 to 5 uses. Clean outside away from valuables! (See
step 8 on page 3).
• Always operate the ash vacuum with the filter installed;
otherwise, dust pass-through or motor damage may result.
• Disconnect power cord from electrical outlet before cleaning
filter, servicing or removing lid.
• Do not use a washing machine to wash filter.
• Do not use hair dryer or microwave to dry filter.
• Filter should be gently tapped to remove ash build-up. Moist
ash will be tough to remove, allow to drying if necessary, then
clean when dry.
• Do not poke at filter or rub filter as this may tear the fabric and
lead to dust pass-through.
• Replace filter once a year, or after about 50 uses or if dust
passes through after filter cleaning, (see instructions for use
step 10 on page 3).
NOTE: General information is given throughout the
manual that may help the operator perform the
operation or service of the machine.
IMPORTANT SAFETY INSTRUCTIONS
SAFE AND EFFECTIVE USE OF THE ASH VACUUM
IS THE OWNER’S RESPONSIBILITY.
When using an electrical appliance, basic precaution should always be
followed, including the following:
READ AND FOLLOW ALL SAFETY INSTRUCTIONS
BEFORE USING THIS VACUUM.
WARNING -
To reduce the risk of fire, electric shock, or injury:
1. Do not leave vacuum cleaner when plugged in. Unplug from
outlet when not in use and before servicing.
2. To reduce the risk of electric shock, do not use outdoors or on
wet surfaces
3. Do not allow to be used as a toy. Close attention is necessary
when used with children nearby.
4. Use only as described in this manual. Use only manufacture’s
recommended attachments.
5. Do not use with damaged cord or plug. If vacuum cleaner is
not working as it should, has been dropped, damaged, left
outdoors, or dropped into water, contact your dealer.
6. Do not pull or carry by cord, use cord as a handle, close lid
on cord, or pull cord around sharp edges or corners. Do not
run vacuum cleaner over cord. Keep cord away from heated
surfaces.
7. When you want to pull the plug from the wall contact, please
do this at the plug itself and not by means of the electrical
cable.
8. Do not handle plug or vacuum cleaner with wet hands.
9. Do not put any object into openings. Do not use with any
opening blocked. Keep exhaust free of dust, lint, hair and
anything that may reduce airflow.
10. Keep hair, loose clothing, fingers and all parts of body away
from openings and moving parts.
11. Turn off all controls before unplugging.
12. Use extra care if used when cleaning stairs.
13. Do not use to pick up flammable or combustible liquids, such
as gasoline, or use in areas where they may be present.
14. Hold plug when rewinding onto cord reel. Do not allow plug
to whip when rewinding.
15. Unplug before connecting the hose.
16. Do not pick up hot embers, hot ash or anything that is burning
or smoking, such as cigarettes or matches.
17. Do not use without filter in place.
18. If the supply cord is damaged, it must be replaced by qualified
person in order to avoid a hazard.
SAVE THESE INSTRUCTIONS
WARNING -
To reduce the risk of electric shock, this vacuum
cleaner has a polarized plug (one blade is wider than the other). This plug
will fit in a polarized outlet only one way. If the plug does not fit fully
in the outlet, reverse the plug. If it still does not fit, contact a qualified
electrician to install the proper outlet. Do not change the plug in any way.
PRECAUTIONARY MEASURES
If the opening that sucks in the air or the suction pipe is
blocked, you should switch off the vacuum cleaner at once.
First clear the blocked substance before you attempt to start
the vacuum cleaner again.
1. Do not operate the vacuum cleaner too close to heaters and
items like radiators, cigarettes, etc.
2. Before you insert the plug into the wall contact, make sure
your hand is dry.
3. When you want to pull the plug from the wall contact, please
do this at the plug itself and not by means of the electrical
cable.
SPECIAL NOTE: THIS VACUUM’S MOTORS ARE EQUIPPED WITH THERMAL
“OVERHEAT” PROTECTION. IF THE MOTORS RUN TOO HOT THEN THEY
WILL SHUT DOWN. YOU MUST WAIT FOR MOTOR TO COOL AND UNPLUG
UNIT IN ORDER TO RE-START VACUUM. CLEANING THE FILTER WILL HELP
PREVENT A REPEAT OF THIS CONDITION.
ASH
VACUUM
2
AC02585_User guide.indd 2 10/25/2013 2:28:01 PM