Marantz VP-10S1 - Manual (Page 7)

3
ENGLISH
• Replacing the lamp runs the risk of burns and electric
shock, therefore shut off power supply, unplug the AC
power cable from its electrical outlet and wait at least 60 min
for the lamp to cool down before attempting to replace it.
• If the lamp breaks, contact your nearest Marantz Authorized
Dealer or Service Center.
• Before replacing the lamp, read carefully “Lamp Handling
Precautions” (
☞
pg. iii) and “Lamp Unit Replacement”
(
☞
pg. 36). Replace the lamp as explained therein.
• The lens of this projector can be changed as liked. (LN-
10VP32/LN-10VP40/LN-10VP53) With the right lens, you
can set the projection distance and screen size according
to the environment of use.
* The above projections distances are given for a
screen with an aspect ratio of 16:9. For screen sizes
and projection distances by lens, see pg. 11-14.
• To change the lens, contact your nearest Marantz
Authorized Dealer or Service Center.
Do not change the lens yourself.
• The lenses used with this projector are as follows.
Lens Changes
WARNING THIS COVER IS PROVIDED WITH
INTERLOCK TO REDUCE THE RISK OF
EXCESSIVE ULTRAVIOLET RADIATION.
DO NOT DEFEAT ITS PORPOSE OR
ATTEMPT TO SERVICE WITHOUT
REMOVING COVER COMPLETELY.
RECYCLE OR DISPOSE
AS HAZARDOUS WASTE DON'T PUT IN TRASH. CONTAINS MERCURY,
CAUTION
Jordforbind altid udstyret Always ground the equipment Jorda alltid utrustningen
ＡＣ１２０Ｖ∼ ６０Ｈｚ Ｘ．ＸＡ
ＭＡＤＥ ＩＮ ＪＡＰＡＮ
ＭＯＤＥＬ ＮＯ．ＶＰ１０Ｓ１／Ｕ１Ｍ
ＦＡＢＲＩＱＵＥ ＡＵ ＪＡＰＯＮ
SERIAL NO. ＡＵＤＩＯ／ＶＩＤＥＯ ＡＰＰＡＲＡＴＵＳ ３６ＶＢ VP10S1/UIM
With FCC Standards Tested To Comply MARANTZ
FOR HOME OR OFFICE USE
Ｎｏ．４３００
∼ AC IN
ON OFF
RS-232C DVI-D IN RGB IN EXT. INT.
IN
OUT
OFF ON
1
2
TRIG. LIGHT REMOTE
VIDEO IN S-VIDEO IN COMPONENT VIDEO IN 1 COMPONENT VIDEO IN 2 Y P B /C B P R /C R Y P B /C B P R /C R
CAUTION HIGH-PRESSURE LAMP MAY EXPLODE IF IMPROPERLY
HANDLED. REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL. CAUTION HOT UNPLUG THE POWER CORD AND WAIT 60
MINUTES BEFORE CHANGING THE LAMP.
ATTENTION LA LAMPE SOUS HAUTE PRESSION PEUT EXPLOSER
SI ELLE, N'EST PAS MANIPULEE CORRECTEMENT,
CONFIER L'OPERATION A UN PERSONNEL D'ENTRETIEN
QUALIFIE.
VORSICHT BEI FALSCHER HANDHABUNG KANN DIE
HOCHDRUCKLAMPE EXPLODIEREN UBERLASSEN SIE
WARTUNGSARBEITEN NUR FACHPERSONAL.
ATTENTION CHAUD DEBRANCER LE CORD ON D'ALIMENTION ET
ATENDER 60 MINUTES AVANT DE CHANGER
LAMPE.
WARNUNG HEISS ZIEHEN SIE DEN NETZSTECKER AB UND
WARTEN SIE 60 MINUTEN BEVOR SIE DIE
GLUHLAMPE WECHSELN.
ランプ交換は、電源プラグをコン
セントから抜いて60分待ってから
行ってください。
高 温 注 意
高圧ランプは誤った扱いをすると
破裂する恐れがあります。万一の
際はサービスマンに依頼をしてく
ださい。 警 告
CAUTION
HIGH-PRESSURE LAMP MAY EXPLODE IF IMPROPERLY
HANDLED. REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
CAUTION HOT
UNPLUG THE POWER CORD AND WAIT 60
MINUTES BEFORE CHANGING THE LAMP.
ATTENTION
LA LAMPE SOUS HAUTE PRESSION PEUT EXPLOSER
SI ELLE, N'EST PAS MANIPULEE CORRECTEMENT,
CONFIER L'OPERATION A UN PERSONNEL D'ENTRETIEN
QUALIFIE.
VORSICHT
BEI FALSCHER HANDHABUNG KANN DIE
HOCHDRUCKLAMPE EXPLODIEREN UBERLASSEN SIE
WARTUNGSARBEITEN NUR FACHPERSONAL.
ATTENTION CHAUD
DEBRANCER LE CORD ON D'ALIMENTION ET
ATENDER 60 MINUTES AVANT DE CHANGER
LAMPE.
WARNUNG HEISS
ZIEHEN SIE DEN NETZSTECKER AB UND
WARTEN SIE 60 MINUTEN BEVOR SIE DIE
GLUHLAMPE WECHSELN.
ラン
セン
行っ
高圧
破裂
際は
ださ
Lamp Replacement Precautions
Lens Projection distance of 100 inch image
LN10VP32 Approx. 125.51 to 156.88 inch
LN10VP40 Approx. 159.88 to 209.18 inch
LN10VP53 Approx. 209.18 to 313.77 inch
Projector Lens
(Found on rear panel nameplate)
VP10S1/U1S SHT(32) LN10VP32
VP10S1/U1S STD(40) LN10VP40
VP10S1/U1S LNG(53) LN10VP53
Note: Pixel defects
DMD
TM (Digital Micromirror Device TM ) is one of the most
advanced technologies for consumer products. The DMD TM
made by high precision technology, however some pixel
defects may be found on the projected image. We are
trying our best to control the quality in order to reduce the
number of defective pixels. It is almost impossible to have
zero pixel defects, even using the most advanced
technology. This is not a problem only for Marantz, but all
DLP
TM projector manufactures. Therefore we have to note
that the warranty does not cover the DMD TM for pixel
defects. We appreciate your understandings.
Note: Lamp
P-VIP lamp is one of the most advanced technologies for
consumer products. The lamp made by high precision
technology, however some lamps might be failing before it
reaches its life. And projector’s brightness is getting darker
along with accumulated lamp usage hours. We are trying
our best to control the quality in order to reduce lamp
failures. It is almost impossible to have zero failure, even
using the most advanced technology. This is not a problem
only for Marantz, but all projector manufactures. Therefore
we have to note that the warranty does not cover the P-VIP
lamp for lamp failures: explosion, and non-lighting except
initial use. And also we have to note that the warranty does
not cover the P-VIP lamp for lamp failures: flickering, and
getting darker along with accumulated lamp usage hours.
We appreciate your understandings.