Marantz PM8200 - Manual (Page 6)

ENGLISH
3
NAMES OF CONTROLS AND INDICATORS
(Page 65)
A
GND (GROUND) terminal
Connect the grounding wire from the Analog turntable to this
terminal.
B
PHONO INPUT jacks
Connect the output jacks of the Analog turntable to these jacks.
C
CD PLAYER INPUT jacks
Connect the output jacks of a Compact Disc player to these
jacks.
D
TUNER INPUT jacks
Connect the output jacks of a tuner to these jacks.
E
AUX/DVD INPUT jacks
Connect the output jacks of DVD player or other AV compo-
nents to these jacks.
F
CD-R IN/OUT jack
Connect the line output jacks and line input jacks of CD re-
corder to these jacks.
G
MD/TAPE IN/OUT jacks
Connect the play (output) jacks and record (input) jacks of
tape decks or MD to these jacks.
H
PRE OUTPUT jacks
Output jack for connection to extension power-amp.
I
REMOTE CONTROL BUS jacks
(REMOTE CONT. BUS)
By connecting this unit with a MARANTZ component equipped
with the remote control (D-BUS) jacks, both components can
be remote controlled as a system.
For details of the remote control function, read the owner’s
manual of the connected component.
The bus OUT terminal is used to send signals to another item
of equipment. The bus IN terminal is used to receive signals
from another item of equipment.
J
SPEAKER Terminals
Connect your speaker system to these terminals.
K
AC IN jack
Connect to AC power outlet.
q
INPUT SELECTOR switch
Selects the program source to be produced, from PHONO,
CD, TUNER, AUX/DVD, CD-R and MD/TAPE. The indicator on
the front panel will be illuminated due to your selected source.
Also, you can use the remote control to select the source.
w
VOLUME control
Turn the knob to adjust the volume. Turning the knob clock-
wise ( ) to increase the volume. The volume up-down opera-
tions can also be controlled from the provided remote control
unit.
e
REC SELECTOR switch
Selects the COPY mode between CD recorder and MD or TAPE
deck, or the signal to be output to the OUT jacks of CD-R and
MD/TAPE.
r
SPEAKERS switch
Press to switch the speaker systems ON (pressed-in position)
and OFF (out position).
Set the switch to OFF (out position) when you listen through
headphones only.
t
PHONES jack
This jack accepts the standard stereo phone plug of head-
phones.
y
IR SENSOR
This unit receives the infrared remote control signal through
this window. Point the transmitter of the remote control unit to-
ward this window to send correct remote control signals.
u
POWER switch
Press the power switch to turn ON/OFF.
When the power is ON, the blue light on the middle of the front
panel and the indicator of the source will be illuminated.
i
Tone (BASS, TREBLE) controls
Turn the knobs to adjust the tone. Turning a knob controls the
level of the corresponding frequency range. Turning each con-
trol toward “+” boosts the corresponding frequency range and
toward “– ” attenuates it.
TREBLE:
Controls the tone of high frequencies.
BASS: Controls the tone of low frequencies.
o
SOURCE DIRECT switch
When you turn on this switch, you can listen the original sound
from the input source. The Tone (BASS, TREBLE) controls
i
and the BALANCE control
!0 cannot be used when this switch
is ON.
!0
BALANCE control
This knob can adjust the output level of the left-right balance.
When this knob is turned fully either clockwise or counter-clock-
wise, the other side of sound cannot be heard from the speaker.
!1
LOUDNESS switch
When this switch is ON, both treble and bass sound will be
emphasised.
!2
MUTE indicator
When you press the mute button on the remote control, this
indicator will be illuminated and the sound is muted.
When you press the MUTE button one more time, or change
the listening volume on the remote control, the MUTE will be
canceled.