Delta 46-464 - Manual (Page 2)

2
6. attach right side leg assembly (K) Fig. 7 to the right side of
extension brace (B) in two holes (Q) as shown using two 3/8-16 x
3-1/2" (89 mm) hex head bolts (E) Fig. 2, four 3/8 flat washers (G)
Fig. 2 and two 3/8-16 nylock nuts (F) Fig. 2. Remember to orient
leg as shown in Fig. 7.
7. attach lathe stand platform (a) Fig. 7 to center support leg using
two 3/8-16 x 3-1/2" (89 mm) hex head bolts (E) Fig. 2, four 3/8 flat
washers (G) Fig. 2 and two 3/8-16 nylock nuts (F) Fig. 2.
NOTE: the stand height is adjustable by placing two bolts through
two of the four holes (R) Fig. 8 in the lathe stand platform. Be sure
the lathe mounting holes (s) Fig. 7 in top of the platform are facing to
outside, away from tool holder as shown.
8. to attach lathe stand platform (s), place 3/8 flat washers on two
bolts and insert bolts through desired two holes (R) Fig. 8. Place
3/8 flat washers on the bolts after insertion and then tighten with
3/8-16 nylock nuts.
NOTE: Be sure each lathe stand platform is set at the same height.
NOTE: Do not tighten completely.
9. attach extension bed to your lathe. Refer to the instruction sheet
with your DELta 46-463 midi-Lathe Extension Bed for attaching
the bed to your lathe. Lift lathe and extension bed onto lathe
stand platforms as shown in Fig. 9.
Risk of unsafe operation. Make sure hardware on
lathe and lathe extension bed is tight.
Risk of unsafe operation. Use two people when
lifting the lathe and lathe bed extensions.
10. match up holes in lathe
base with holes in platform.
attach lathe to stand at these
holes using four 3/8-16 x 1-1/2"
(38 mm) hex head bolts (B)
Figure 10, eight 3/8 flat washers
and four 3/8-16 nylock nuts (a).
11. For each hole, place a washer
on the hex head bolt and insert
it down through the hole at (B)
Fig. 10. Place a second washer
on bolt underneath and tighten
securely using nylock nut.
12. tighten all lathe stand hardware firmly at this point.
13. adjust all leveling feet so the lathe stand rests securely on the
floor without rocking or tilting. then tighten all four jam nuts.
Refer to the instruction sheet with your DELta 46-463
midi-Lathe Extension Bed for all relevant safety rules when using the
lathe with the extension.
TROUBLESHOOTING
For assistance with your machine, visit our website
at www.deltaportercable.com for a list of service centers or call the
DELta machinery help line at 1-800-223-7278 (in Canada call 1-800-
463-3582).
SERVICE
REPLACEMENT PARTS
Use only identical replacement parts. For a parts list or to order parts,
visit our website at www.deltaportercableservicenet.com. You can
also order parts from your nearest factory-owned branch, authorized
warranty service Center or by calling End User services at (800) 223-
7278 to receive personalized support from one of our highly-trained
representatives.
SERVICE AND REPAIRS
all quality tools will eventually require servicing and/or replacement
of parts. For information about DELta machinery, its factory-owned
branches, or to locate an authorized warranty service Center, visit
our website at www.deltaportercable.com or call our End User
services at (800) 223-7278. all repairs made by our service centers
FiG. 5
FiG. 6
FiG. 7
FiG. 9
B
m
C
N
C
P
K
B
Q
a s
h
m
h
h
R
FiG. 8
h