Chapter 2 - hardware installation, System board layout, System memory – DFI BT101 User Manual
Page 9: Rear i/o onboard i/o storage expansion, Chapter 2 hardware installation, Features • two 204-pin ddr3l sodimm sockets, Ddr3l-1 ddr3l-2 standby power led, Intel
www.dfi .com
9
Chapter 2 Hardware Installation
Chapter 2
Chapter 2 - Hardware Installation
Board Layout
System Memory
Features
•
Two 204-pin DDR3L SODIMM sockets (
-E45/-E26/-J00
)
- up to 8GB system memory
- dual channel memory interface
One 204-pin DDR3L SODIMM socket (-E25/-E15)
- up to 4GB system memory
- single channel memory interface
•
Supports DDR3L 1333MHz (-E45/-J00)
Supports DDR3L 1066MHz (-E26/-E25/-E15)
Important:
Electrostatic discharge (ESD) can damage your board, processor, disk drives, add-in
boards, and other components. Perform installation procedures at an ESD workstation
only. If such a station is not available, you can provide some ESD protection by wear-
ing an antistatic wrist strap and attaching it to a metal part of the system chassis. If
a wrist strap is unavailable, establish and maintain contact with the system chassis
throughout any procedures requiring ESD protection.
Important:
When the Standby Power LED lights red, it indicates that there is power on the sys-
tem board. Power-off the PC then unplug the power cord prior to installing any de-
vices. Failure to do so will cause severe damage to the motherboard and components.
Rear I/O
Onboard I/O
Storage
Expansion
SPI Flash
BIOS
COM 3
COM 2
COM 4
1
2
11
12
Front
Panel
1
2
10
9
COM 1
1
2
10
9
1
2
10
9
1
2
10
9
1
2
6
5 1
2
6
5 1
2
6
5 1
2
6
5
1
2
9
10
8 7
2 1
LAN2 State
LAN2 State
LAN1 State
LAN1 State
2
1
39
40
LVDS LCD Panel
1
SATA 1
1
SATA 0
1
LCD/Inverter Power
Digital I/O
1 1 1
(JP17)
(JP18)
(JP20)
Buzzer
Digital I/O Power Select
Digital I/O 3/5/7/9 Output State
Digital I/O 11/13/15/17 Output State
(JP17)
(JP18)
(JP20)
1
1
1
1
1
1
1
LAN 1
LAN 2
DC-in
ATX power (optional)
USB 0-1
USB 2.0
USB 3
DVI-I
1
USB 6-7 Power Select
SATA DOM Power Select
Auto Power-on Select
(JP10)
(JP12)
(JP13)
COM 1 RS232/422/485 Select
COM 1 RS232/Power Select
Backlight Power Select
Panel Power Select
LCD/Inverter Power Select
(JP16)
(JP19)
(JP21)
Dimming Mode Select
(JP15)
USB 3.0
1
Note:
SATA 0 supports SATA DOM.
Chassis
Intrusion
1
Mini PCIe
2
1
10
9
USB 4-5
USB 2.0
2
1
10
9
USB 6-7
Battery
1
4
SATA
Power 1
Standby
Power LED
1
CPU Fan
1
System
Fan
1
2
19
1
1
Line-out
S/PDIF
(JP21)
(JP15)
(JP16)
(JP19)
(JP10) (JP12)
(JP13)
PS/2 KB/MS
Power Select (JP6)
SATA 2.0
SATA 2.0
USB 4-5 Power
Select (JP5)
12
10
3
1
Mini PCIe/mSATA
Signal Select (JP2)
Mini PCIe/mSATA
Power Select (JP1)
USB 3 Power
Select (JP3)
USB 0-1 Power
Select (JP4)
(JP8) (JP9) (JP11) (JP14)
PS/2 KB/MS
Clear CMOS Data (JP7)
(JP8)
(JP9)
(JP11)
(JP14)
6
5
2
1
SMBus
12
10
3
1
SATA 1/mSATA Signal
Select (JP22)
PCIe x1
DDR3L_2 SODIMM
DDR3L_1 SODIMM
1
4
SATA
Power 0
Intel
BGA 1170
1
12
2
11
LPC
1
10
9
2
Front Audio
1
1
1
1
2
5
6
2
SMSC
USB4604
Intel
WGI210AT
Intel
WGI210AT
ASMedia
ASM1442
NXP
PTN3460
Realtek
ALC888
DDR3L-1
DDR3L-2
Standby
Power LED