Cybex 18000-FT-325 Bravo - Manual (Page 9)

9
Cybex Owner’s Manual
• Area is not in the vicinity of high humidity, such as in the vicinity of a steam room, sauna, indoor
pool or outdoors. This unit is designed to function normally in an environment with a relative
humidity range of 30% to 75%.
Exposure to extensive water vapor, chlorine and/or bromine could adversely affect the electronics as
well as other parts of the unit.
• Area maintains an ambient temperature range of 50° F (10° C) to 104° F (40° C) degrees.
Tools Required
• 9/16” Wrench
• 7/32” Allen wrench
• 1/8”Allen wrench
• 3/4” Socket or wrench
• Hammer
• 3/16” Pin punch
• Loctite ® #242
Assembly Procedure
Two people will be required for this procedure.
Read and understand all instructions thoroughly before assembling this unit. Check all items
carefully. If there is damage, see the Customer Service section of this manual for proper procedure to
return, replace, or reorder parts.
Verify parts list shown below.
Qty Part Number Description Diagram
4 16010-311 Foot pad
1 DE000006 Decal (5-75)
2 2 DE000006
DECAL, WT PLATE (5 - 75) 2:1
6-5-13 REL
125 1:1
OWATONNA
MFG. APPR.
TECH. PUBS. APPR. DATE DATE
REV. DWG. NO. SCALE SIZE
CHECKED BY
DWG. BY
TITLE:
FINISH:
MATERIAL:
B SHEET
OF
EXCEPT AS NOTED
GENERAL TOLERANCES:
2 DECIMALS ± .03
3 DECIMALS ± .015 ANGLES ± 1°
FEATURES SHOWN
PERPENDICULAR OR PARALLEL SHALL BE SO WITHIN ± 1°
REMOVE ALL BURRS BREAK SHARP EDGES .005/.010 R
SURFACE FINISH
INDICATED PER ANSI B46.1-1985
GENERAL MACHINING
DIMENSIONS IN INCHES
DATE DATE REMOVE CARBURIZATION AND SCALE FROM LASER AND PLASMA CUT EDGES
ALL MATERIAL MUST COMPLY TO EUROPEAN UNION DIRECTIVE 2002/95/EC RoHS (RESTRICTION OF HAZARDOUS SUBSTANCES)
_
NOTES:
1. FONT - 40 POINT ARIAL BOLD. HORIZONTAL SCALE 80%. TRACKING -50.
50
22.7 34.0 31.8
55
27.2 25.0
75 70 65 60 10
4.5 20.4 11.3 15.9 13.6 18.1
20
9.1 6.8
40 35 30 25 5 45 15
2.3 29.5
1 DE000007 Decal (80-100)
125 1:1
OWATONNA
MFG. APPR.
TECH. PUBS. APPR. DATE DATE
REV. DWG. NO. SCALE SIZE
CHECKED BY
DWG. BY
TITLE:
FINISH:
MATERIAL:
B SHEET
OF 2 2
EXCEPT AS NOTED
GENERAL TOLERANCES:
2 DECIMALS ± .03
3 DECIMALS ± .015 ANGLES ± 1°
FEATURES SHOWN
PERPENDICULAR OR PARALLEL SHALL BE SO WITHIN ± 1°
REMOVE ALL BURRS BREAK SHARP EDGES .005/.010 R
SURFACE FINISH
INDICATED PER ANSI B46.1-1985
GENERAL MACHINING
DIMENSIONS IN INCHES
DATE DATE REMOVE CARBURIZATION AND SCALE FROM LASER AND PLASMA CUT EDGES
ALL MATERIAL MUST COMPLY TO EUROPEAN UNION DIRECTIVE 2002/95/EC RoHS (RESTRICTION OF HAZARDOUS SUBSTANCES)
DE-000007
6-5-13 REL
_
DECAL, WT PLATE (80-100) 2:1
NOTES:
1. FONT - 40 POINT ARIAL BOLD. HORIZONTAL SCALE 80%. TRACKING -50.
36.3 45.4 43.1 38.6 40.8
80 100 95 85 90
1 4800-433 Rope Handle