Dish Network 104333 User Manual
Dish Network Remote control
104333
1
T
ABLE
OF
C
ONTENTS
About the Remote Control............................... page 2
Remote Control Signals: UHF or IR.................page 2
Installing Batteries in the Remote Control........page 3
Remote Control Modes ....................................page 3
Using the Remote Control Buttons ................ page 4
SAT (Satellite Receiver) Mode.........................page 4
TV (Television) Mode .......................................page 8
VCR (VideoCassette Recorder) Mode.............page 10
AUX (Auxiliary) Mode for Cable TV Box ..........page 12
AUX (Auxiliary) Mode for Tuner or Amplifier....page 13
Remote Control Procedures............................ page 15
Controlling a Device.........................................page 15
Changing the Remote Control Address ...........page 16
Installing an Attenuator ....................................page 17
Controlling Sound Volume................................page 18
Receiver Volume Control...................... page 18
TV or Amplifier Volume Control ............ page 19
Doing the Device Code Scan...........................page 20
Finding the Device Codes................................page 21
Device Codes ................................................... page 22
TVs...................................................................page 22
VCRs................................................................page 23
DVD Players ...................................................... page 25
Tuners and Amplifiers ......................................page 25
Cable TV Boxes ...............................................page 25
Trouble-Shooting Table ................................... page 26
Limited Warranty .............................................. page 28
If You Need Help ............................................... page 30
Document Outline
- Important Regulatory Factors
- Wireless Remote Control
- Important Safety Instructions
- Table of Contents
- About the Remote Control
- Using the Remote Control Buttons
- SAT (Satellite Receiver) Mode
- SAT Mode Button
- AUX Mode Button
- TV/Video Button
- Menu Button
- Power Button
- Page Up and Page Down (Arrow) Buttons
- Mute Button
- Volume Button
- Guide Button
- Select Button
- Up/Down/Left/Right (Arrow) Buttons
- Recall Button
- Information (Info) Button
- View Button
- Cancel Button
- System Information (Sys Info) Button
- Number Buttons
- Pound Button
- TV (Television) Mode
- VCR (VideoCassette Recorder) Mode
- AUX (Auxiliary) Mode for Cable TV Box
- AUX (Auxiliary) Mode for Tuner or Amplifier
- SAT (Satellite Receiver) Mode
- Remote Control Procedures
- Controlling a Device
- 1. Turn ON the device you want the remote to control, using the device’s buttons or the remote co...
- 2. Find the brand name of the device in the tables that start on page22. If the brand is not lis...
- 3. Press and hold the mode button for the device that you want the remote to control, for about t...
- 4. Use the number buttons to enter the code for the device. Note: For the AUX mode, you must ente...
- 5. Press and release the Pound (#) button. If the code is valid, the mode button backlight blinks...
- 6. Test if the code works for the device by pressing the Power button. If the code works, the dev...
- 7. Turn the device back ON and try some other buttons to make sure they work. Sometimes, the Powe...
- 8. If the code you entered does not work, repeat steps 3 through 7 using another code from the ta...
- 9. If you have tried all of the codes listed for the device without success, or if you cannot fin...
- Changing the Remote Control Address
- 1. Display the Important System Information menu. Note the Remote Address shown on this menu.
- 2. Press and hold the SAT mode button about three seconds, until all the mode button backlights c...
- 3. Use the number buttons to enter a number from 1 to 15. The SAT mode button backlight will blin...
- 4. Press the Pound (#) button. If the address you entered is valid for the remote control, the SA...
- 5. Press the Record button. The Remote Address on the Important System Information menu should ma...
- 6. To check the address, press and hold the SAT mode button for three seconds. Then, press the Po...
- 7. Press the Select button.
- Installing an Attenuator
- Controlling Sound Volume
- Receiver Volume Control
- 1. Use the TV remote control to make sure that the TV sound volume is not turned down or muted. N...
- 2. Press the Menu button.
- 3. Select the System Setup option.
- 4. Select the Volume Control option. Note: If the System Setup menu does not display this option,...
- 5. Select the TV remote volume control or the DISH remote volume control option.
- 6. Select the Save option.
- 7. If you are setting up the remote control for the first time, see Controlling a Device on page...
- TV or Amplifier Volume Control
- 1. Press and hold the AUX mode button for three seconds, then release it.
- 2. Press the Pound (#) button.
- 3. Press the plus (+) side of the Volume button.
- 4. Press the 0 number button.
- 5. Press the Pound (#) button. The AUX mode button backlight blinks three times.
- 1. Press and hold the TV mode button for three seconds, then release it.
- 2. Press the Pound (#) button.
- 3. Press the plus (+) side of the Volume button.
- 4. Press the 0 number button.
- 5. Press the Pound (#) button. The AUX mode button backlight blinks three times.
- Receiver Volume Control
- Doing the Device Code Scan
- 1. Press and hold the mode button for the device, for about three seconds. When all the other mod...
- 2. For AUX mode only, use the number buttons to enter a number as follows: 0 is for a second TV, ...
- 3. Press the Power button.
- 4. Press the Up or Down arrow button to set the remote to the next code. The Down arrow button sc...
- 5. When the remote reaches the correct code, the device turns OFF. If this happens, press the Pou...
- 6. Press the Power button to turn the device back ON.
- 7. Try some other remote control buttons to make sure that you have the right code.
- Finding the Device Codes
- Controlling a Device
- Device Codes
- Trouble-Shooting Table
- Limited Warranty
- If You Need Help
- 1. Review this Guide.
- 2. See the Trouble-Shooting Table on page26.
- 3. Call the DISH NetworkSM Service Center at 1-800-333-DISH (3474). Have the date of purchase and...
- 4. A Representative will assist you. He or she will try to troubleshoot any problem you may be ha...
- 5. If the Representative finds that you should return the remote control, he or she will give you...
- 6. You must package returned equipment properly. Follow the instructions that the Representative ...
- 7. Write the RA number in large, clearly visible characters on the outside of the shipping box us...
- 8. We will: