Comtech EF Data FX Series Quick Start Guide User Manual
Page 6
6
FX Series Quick Start Guide
Section: FX Series Installation Pattern (WCCP)
10. Click “WCCP”
a. Click “Add WCCP Definition”
b. Select the IP address of the
interface that will send the
WCCP messages
the “Source IP address”
selection box.
c. Enter the routers IP address in
the “Router address” field.
d. Select the local interface that
will receive the GRE traffic if
using GRE redirection. If using L2
redirection leave blank.
e. If using GRE redirection enter
the router identifier of the
router in the “Remote GRE
tunnel address” field. If using L2
redirection leave blank.
f. Use default value for
“Enablement”.
g. Use default value for “Critical”.
h. Select Redirection method.
i. Select the same value used
Redirection method.
j. For L2 use Mask Assignment scheme. For GRE use Hash Assignment scheme. * This may
differ on highest end Cisco equipment.
k. Leave the password field blank, unless one was configured for WCCP on the Cisco device.
l. If using “web-cache” W
“Service group number” field. If using source IP address preservation use the default value.
NOTE: See FX Series Admin Guide v6.01 Section 5.3 for details and difference.
m. Use the default values for “Redirect based on”, Accept traffic for”, and “Ports”.
n. If using source IP address preservation select “Enabled” for “Use additional service group”. If
using “web-cache” default this value.
o. Click “Add WCCP Definition”
11. Click “Status”, then click “Real
FX Series Quick Start Guide – Installation Patterns
Guide - Version 6.0 Rev 1
FX Series Installation Pattern (WCCP)
MN
For More information
http://www.comtechefdata.com/stampedeDocs.asp
Click “Add WCCP Definition”
Select the IP address of the
interface that will send the
WCCP messages to the router in
the “Source IP address”
Enter the routers IP address in
the “Router address” field.
Select the local interface that
will receive the GRE traffic if
using GRE redirection. If using L2
redirection leave blank.
edirection enter
the router identifier of the
router in the “Remote GRE
tunnel address” field. If using L2
redirection leave blank.
Use default value for
Use default value for “Critical”.
Select Redirection method.
Select the same value used for
Redirection method.
For L2 use Mask Assignment scheme. For GRE use Hash Assignment scheme. * This may
differ on highest end Cisco equipment.
Leave the password field blank, unless one was configured for WCCP on the Cisco device.
cache” WCCP redirection (no source IP address preservation) enter 0 in the
“Service group number” field. If using source IP address preservation use the default value.
NOTE: See FX Series Admin Guide v6.01 Section 5.3 for details and difference.
values for “Redirect based on”, Accept traffic for”, and “Ports”.
If using source IP address preservation select “Enabled” for “Use additional service group”. If
cache” default this value.
Click “Add WCCP Definition”
k “Real-Time Monitor”, then click “Restart Service”.
Installation Patterns
MN-FXADMIN6-QSG Rev 1
For More information Tel: 1-937-291-5035
http://www.comtechefdata.com/stampedeDocs.asp
For L2 use Mask Assignment scheme. For GRE use Hash Assignment scheme. * This may
Leave the password field blank, unless one was configured for WCCP on the Cisco device.
CCP redirection (no source IP address preservation) enter 0 in the
“Service group number” field. If using source IP address preservation use the default value.
NOTE: See FX Series Admin Guide v6.01 Section 5.3 for details and difference.
values for “Redirect based on”, Accept traffic for”, and “Ports”.
If using source IP address preservation select “Enabled” for “Use additional service group”. If