TVLogic SWM-170A - Manual (Page 16)

30 Multi Format LCD Monitor Multi Format LCD Monitor 31
[9] SYSTEM
5. Menu Operations
●
KEY LED
- This item controls KEY LED ON/OFF.
- If the button with LED is pressed with the
KEY LED Off, LED comes on but goes off after
5 seconds later.
●
F1/DOWN MAPPING
- User can select the function for the F1
button.
- Selectable functions: SCAN, ASPECT,
TIMECODE, CC SEL., ALM SEL., VIDEO RANGE,
FAST MODE, DITHERING, FILTER, FORCE Psf,
UMD, COLOR TEMP, PAGE 801, PAGE 888,
PAGE 889, MARKER DISPLAY and FREEZE.
●
F2/UP MAPPING
- User can select the function for the F2
button.
- Selectable functions: SCAN, ASPECT,
TIMECODE, CC SEL., ALM SEL., VIDEO RANGE,
FAST MODE, DITHERING, FILTER, FORCE Psf,
UMD, COLOR TEMP, PAGE 801, PAGE 888,
PAGE 889, MARKER DISPLAY and FREEZE.
PAGE II >> PAGE III
KEY LED
F1/DOWN MAPPING
F2/UP MAPPING
ON
FREEZE
SCAN
SWM-170A SDI A 1080/60i
[9] SYSTEM [10] INFO.
5. Menu Operations
●
DEVICE
- Used to select the device for color
calibration.
- Available Device : K-10, Eyeone Display Pro,
Specbos 1211.
●
COLOR CALIBRATION
- Connect the COLOR PROBE(e.g. K-10) to the
USB port to calibrate the monitor without a
PC.
* Refer to the section “Firmware Upgrade &
Color Calibration” for more information.
●
TARGET LUMINANCE
- Used to set the luminance.
●
K-10 CHANNEL
- Used to select the channel of COLOR
PROBE(K-10)
- Available only when the Color Probe is K-10.
●
COLORSPACE
- This function is not supported.
●
CALIBRATION START
- Used to start the calibration.
- Set the Calibration as [On]. The Color
calibration start menu will activate after the
Color Probe connection is completed.
●
MEASUREMENT
- Used to start the calibration.
Set the Color Calibration as [On]. The Color
calibration start menu will activate after
the USB connection is completed.
●
COPY DATA
- Used to copy the files related to the
calibration.
●
CAL. LOG COPY START
- Used to save the CALIBRATION LOG file on a
USB drive.
* Set the COPY DATA as [On]. Activates
only when the USB drive(Thumb drive) is
connected.
●
S/W UPGRADE
- Used to upgrade the firmware using the USB
(Thumb drive).
* See section “6. Firmware Upgrade & Color
Calibration” for more information.
●
S/W UPGRADE START
- Used to start S/W upgrade. If the USB drive
is detected, the firmware upgrade becomes
activated.
PAGE III >> PAGE VI
DEVICE
COLOR CALIBRATION
TARGET LUMINANCE
K-10 CHANNEL 00:
COLORSPACE
CALIBRATION START
MEASUREMENT
PAGE VI >> PAGE I
COPY DATA
CAL. LOG COPY START
S/W UPGRADE
S/W UPGRADE START
K-10
OFF
100cd/m 2
SWM-170A SWM-170A SDI A SDI A 1080/60i 1080/60i SWM-170A SDI A
BOARD VERSION 0001 01 0.01 9
SUB VERSION 00.00.00.00
BRIG : 0
CONT : 0
COLOR : CUSTOM1
SCAN : ZERO
ALM : 16 CH
C.C : OFF
T.C : OFF
1080/60i
KEYPAD VERSION
MCU VERSION
FPGA VERSION
GPU VERSION
●
INFO.
- Displays the Board version and current status
information.
- BOARD VERSION : 0001(GPU) 01(FPGA)
0.01(MCU) 7(KEYPAD)
- SUB VERSION : 00.00.00.00(NETWORK)
- BRIG. : Brightness
- CONT. : Contrast
- COLOR : Color Temp
- SCAN : Scan Mode
- ALM : Audio level meter
- C.C : Closed caption
- T.C : Timecode