beautypg.com

Denon AVR-487 User Manual

Page 23

background image

System Setup

System Setup

ENGLISH

20

ENGLISH

Setting the EXT. IN Subwoofer Level

Press

ENTER

or

H

H

to enter the setting and switch to

the Auto Preset Memory setting.

2

Sets the playback level of the analog signal that was input to the EXT.
IN subwoofer terminal.

+15 dB, +10 dB, +5 dB, 0 dB:

Sets the playback level of the analog signal that was input to the
EXT. IN subwoofer terminal.

Press

F

F G

G

to set.

1

Setting the Auto Preset Memory

Up to 56 FM stations can be preset automatically (

page 30).

Press

F

F

to start.

• “CH” blinks on the display and searching begins.
• “Completed” appears once searching is completed.

• If an FM station cannot be preset automatically due to poor

reception, use the “Manual tuning” operation (

page 31) to tune

in the station, then preset it using the manual “Preset memory”
operation (

page 31).

1

Press

ENTER

to enter the setting and switch to the

Option Setup.

2

S

e

a

r

c

h

1

C

O

M

P

L

E

T

E

D

2

6

E

X

T

.

I

n

S

W

+

1

0

1

7

P

r

e

s

e

t

<

S

t

a

r

t

2

Option Setup

Setting the Volume Control

This sets the volume level of output.

Press

D

D H

H

to select the item, then press

F

F G

G

to set.

Volume Limit:

Set the volume’s upper limit.

0 dB, –10 dB, –20 dB:

The volume cannot be increased above the selected levels.

OFF:

If you do not want to set a volume limit, select “OFF”.
In this case, the volume can be set to the AVR-487’s maximum
volume (output) level of +18 dB, which is extremely loud.

2

Muting Level:

Set the level of volume attenuation in the mute mode.

FULL:

The volume is fully muted.

–40 dB, –20 dB:

The volume is lowered 40 dB or 20 dB from the current level.

Power On Volume Level:
LAST:

The volume set when the AVR-487 was last used is stored in the
memory and set when the power is turned on.

– – – (Mute):

The volume is always muted when the power is turned on.

–80 dB ~ +18 dB:

Set the volume level when the power is turned on.
You can adjust the volume level within the range of –80 to +18 dB.

Press

ENTER

or

H

H

to enter the setting and switch to

the Auto Surround Mode setting.

3

Press

F

F G

G

to select “3. Op”, then press

ENTER

.

1

1

O

p

t

i

o

n

S

e

t

u

p

4

AutoSurr. ON

3

2

P

.

O

n

L

A

S

T

3

M

u

t

e

F

U

L

L

1

L

i

m

i

t

-

1

0

d

B

2

Setting the Auto Surround Mode

Set whether or not to store the surround mode last played for the
input signal.
The surround mode used at last for the three types of input signals
shown below is stored in the memory, and the signal is automatically
played with that surround mode the next time it is
input.

q Analog and PCM 2-channel signals (STEREO)
w 2-channel signals of Dolby Digital, DTS or other multi-channel

format (DOLBY PL

II

x Cinema)

e Multi-channel signals of Dolby Digital, DTS or other multi-

channel format (DOLBY/DTS SURROUND)
Default settings are indicated in ( ).

Press

ENTER

to enter the setting and switch to the

Speaker Setup.

2

Press

F

F G

G

to set.

1

4

A

u

t

o

S

u

r

r

.

O

F

F

1

2