Ryobi RP4310 - Manual (Page 7)

7 – English
OPERATION
WARNING:
Do not allow familiarity with products to make you care-
less. Remember that a careless fraction of a second is
sufficient to inflict serious injury.
WARNING:
Always remove battery pack from the product when you
are assembling parts, making adjustments, cleaning, or
when not in use.
WARNING:
Do not use any attachments or accessories not recom-
mended by the manufacturer of this product. The use
of attachments or accessories not recommended could
result in property damage or malfunction of the product.
INSTALLING THE MOUNTING BRACKET
See Figure 2, page 10.
A convenient wall mount bracket is included for hanging
your key lock box and storing keys on or near the item you
want to secure.
Once the key lock box is installed and secured onto the
mounting bracket, the screws for the mounting bracket can
not be accessed without removing the unit.
 Select a suitable, sturdy location for hanging the key box
before installing the mounting bracket. This will help to
decrease the chance of mechanical failure.
 When selecting a location for installing the mounting
bracket, make sure there is adequate space for opening
the key door and operating the key lock box. There should
not be any wiring behind the location where you will be
drilling holes for the mounting bracket.
 Using the bracket as a guide, mark the location of the
two holes for the included screws and drill the holes.
 If mounting into drywall, you may wish to use the included
drywall anchors.
 Insert the screws into the holes and tighten them to secure
the mounting bracket.
 Install and secure the key lock box.
TO OPEN/CLOSE THE DOOR KNOB LOOP
See Figures 2 - 3, page 10.
Your key lock box is designed to hang on a standard door
knob or the included mounting bracket.
 Enter any stored code, press the door release button,
and press
OPEN to open the key door.
 With the key door open, hold the unit and pull down firmly
on the key door. The door knob loop on top of the unit
will be released.
 To lock the door knob loop, push the free end into the
unit until it clicks into place.
NOTE: The door knob loop can only be locked while the
key door is open.
WARNING:
Always remove battery pack from your battery product
when you are assembling parts, making adjustments,
cleaning, or when not in use. Removing battery pack
will prevent accidental starting that could cause serious
personal injury.
TO INSTALL/REMOVE THE BATTERY PACK
See Figures 4 - 7, page 11.
To install the battery pack:

To open the key door, insert a backup key into the lock
on the side of the key lock box, press and hold the door
release button, and turn the key.
 The key storage compartment is on the right side of the
key drawer. The battery compartment is on the left.
 To open the battery door, push the tab in the direction
indicated by the
OPEN arrow.
 Insert the battery pack in the direction shown. Make sure
the raised rib on the battery pack aligns with the groove
in the compartment.
 Close the battery door and push the thumb tab to the
right to close.
 Push up on the key door to close and lock it.
 With the battery pack installed, the unit is ready for setting
codes.
 Do not attempt to use this product if the battery cap is
not securely closed.
To remove the battery pack:

Enter any stored code, press the door release button, and
press
OPEN to open the key door. You can also insert a
backup key into the lock on the side of the key lock box,
press and hold the door release button, and turn the key
to open the door.
 Push the tab to open the battery door.
 Remove the battery pack.
NOTE: If the battery pack is removed, codes will be retained
in memory.
SETTING TIME AND DATE
See Figure 8, page 11.
When a battery pack is inserted, the display enters Time and
Date Set mode. All digits will blink twice, and then the Hour
segment will blink.
NOTE: After you have set the hour, the minutes, year, month,
and date sections will also blink when they are ready to
set.