beautypg.com

Replacement parts optional parts – ParkZone PKZ1800 User Manual

Page 9

background image

16

17

1. Don’t fly in winds over 10 mph! If you are a less

experienced pilot, this is especially important.

2. A pilot who has never flown a 3-channel plane with

pitch control should get help from an experienced

radio control pilot during first flights. Pilots who

have not flown a 3-channel plane at all should not

fly unless an experienced RC pilot is present to

guide them.

3. Choose your flying field carefully—grass and soft

ground with a 600-foot (183-meter) diameter of

open space is optimal for flying and will lengthen

the life of your airplane. Make sure there are no

obstacles that will get in your way when flying,

such as trees or buildings. Make sure you do not

fly where there are pedestrians who could be hurt

by the airplane.

4. Remember that holding the stick full over for too

long can cause the airplane to spiral dive and

crash. At the very first sign of the plane beginning

to spiral down, immediately release the stick and

give the opposite turn control to the spiral, then

pull back on the elevator gently to level flight and

level the wings.

Repairing Minor Damage

ParkZone 18-Amp ESC

Success Tips

5. Don’t attempt to fly or do maneuvers beyond your

flying abilities. Seek the assistance of an experi-

enced pilot when trying new maneuvers that are

more extreme and involve fast flight.

6. If you’re gliding with the motor off, allow your plane

more area for turns.

7. Position yourself at your flying field so that you

keep the sun at your back and out of your eyes.

Wear sunglasses on bright days.

8. Keep the aircraft upwind, especially on windier

days, to prevent it from “flying away.” The wind is

normally stronger at higher altitudes than it is on

the ground.

9. Keep your plane in front of you so you don’t have

to turn in circles as you fly. Try to avoid flying

directly overhead.

If you happen to crash, and part of the fueslage or wing
breaks, you can repair the damage by using regular
medium CA glue to glue the pieces back on, or packing
tape to cover the missing pieces. However, if the
damage is severe, or if the wings and/or tail,are bent,
replace the damaged parts prior to flying again. See the
last few pages of the manual for a complete list of
replacement parts for your P-51D Mustang.

Note: Horizontal stabilizer is not compatible with

regular CA. Use foam-safe CA or replace stabilizer

if damaged.

Specifications

Continuous Current: 18A*

Max Burst Current: 25A (15 sec)*

Length: 47.0mm

Width: 27.5mm

Height: 8.5mm

Weight: 31.0 g

Cells: 2-3S LiPo or 6-12 NiMH/NiCd

Battery Input Leads: 16AWG with E-flite

EC3 Connector

Motor Output Leads: 16AWG with 3.5mm Female
Gold Bullet Connectors

* Proper cooling required

Default Settings

9V Cutoff

No Brake

Motor Timing: 15 Degrees

Throttle Input: 1.2–1.8ms

Optional RS232 Serial Link & Programming Software
Programming your ESC will be much faster and easier
when you purchase the optional RS232 Serial Link and
programming software. This will allow you to update your
ESC using a laptop or PC. You must have a Serial Port
on your computer or you can purchase a separate USB
to DB9 adapter (available at computer retailers).

EFLARS232—RS232 Serial Link/Programming Software

For specific ESC programming instructions please refer
to horizonhobby.com

Replacement Parts

Optional Parts

PKZ1019 Propeller 9 x 6
PKZ1020 Prop Adapter
PKZ1033 11.1V 1300mAh Li-Po Battery

with EC3 Connector

PKZ1081 SV80 Long Lead 3-Wire Servo
PKZ1771 Tx: CH 1, 26.99
PKZ1772 Tx: CH 2, 27.04
PKZ1773 Tx: CH 3, 27.09
PKZ1774 Tx: CH 4, 27.14
PKZ1775 Tx: CH 5, 27.19
PKZ1776 Tx: CH 6, 27.25
PKZ1802 Decal Sheet
PKZ1807 Spinner
PKZ1813 Clear Canopy and Painted Hatch
PKZ1814 18A Brushless ESC
PKZ1820 Bare Wing (Painted, No Decals or Servos)
PKZ1822 Pushrods with Clevis
PKZ1823 Control Horn set
PKZ1824 Horizontal Stabilizer with Accessories
PKZ1825 Motor Mount
PKZ1826 Cowl with Exhaust
PKZ1867 Bare Fuselage (Painted, No Decals)
PKZ1870 Replacement Airframe
PKZ4416 480 Brushless Outrunner Motor, 960Kv
PKZ4418 Motor shaft: 480 Outrunner
PKZ4551 Rx: CH 1, 26.99
PKZ4552 Rx: CH 2, 27.04
PKZ4553 Rx: CH 3, 27.09
PKZ4554 Rx: CH 4, 27.14
PKZ4555 Rx: CH 5, 27.19
PKZ4556 Rx: CH 6, 27.25
HBZ1003 DC Li-Po Balancing Charger

HBZ1004 1.5A AC Power Supply