Palram SUNTU Plus - Manual (Page 9)

Greenhouse Installation Guide
7
Additional Accessories
1. Omega Purlins: Palram recommends building
the greenhouse utilizing special Omega
shaped purlins to prevent condensation
drips from the purlins. Care must be taken
to collect the condensation water at the
edge of the purlins.
Fastening Metal Profile: it is possible
to install a special sheet metal angle
profile for tightening the roof sheets
along the purlins. The profile will be
30 x 40mm, 2mm thick.
Fastening distance – no more than 1200 mm.
Special care must be taken to fasten the angel
profile on top of the Side-lap/mid crests,
without over tightening, to avoid distorting
the corrugations.
2. Corner / Side Ridge Closure: Two adjoining galvanized
sheet-metal covering profiles (flashings) are used for
closing the cladding sheets where the roof meets the
gable wall, or a vertical closure between two walls corner.
a) the internal 100x100x1.5 mm profile is used to attach
both edges of the cladding sheets to the structure.
b) the external 150x150x0.6 mm flashing profile will fasten
to the internal profile through the cladding sheets and
will close the gap between them, at the corner.
Sheet-to-Sheet Stitching Fasteners
Side-lap profiles Stitching Fasteners
Top and bottom pre-drilled metal side-lap profiles are
recommended for improved tightening of lapping sheets,
between purlins, with 1/4" x 1” self-tapping screws every 400
mm and 1/4" x 2” self-drilling screws above each purlin. Stitching Fasteners: It is possible to use 1/4" x 3/4” self-
tapping screws every 400 mm at the side-lap crest top for
stitching the lapping sheets.
copertura angolare
metallica superiore
150 X 150 X 0.6mm
copertura angolare
metallica inferiore
100 X 100 X 1.5 mm
Coperture Angolari
Profilo Omega
Trave di sostegno Supporto a Omega
SUNTUF® Plus
Sigillatura corrugata
SUNTUF® Plus SUNTUF® Plus
SUNTUF® Plus SUNTUF® Plus
copertura angolare
metallica superiore
150 X 150 X 0.6mm
copertura angolare
metallica inferiore
100 X 100 X 1.5 mm
Coperture Angolari
Profilo Omega
Trave di sostegno Supporto a Omega
SUNTUF® Plus
Sigillatura corrugata
SUNTUF® Plus SUNTUF® Plus
SUNTUF® Plus SUNTUF® Plus
Sheet-to-sheet fastening screw between overlapping
corrugations (detail), for Omega profile.
Sheet-to-sheet fastening screw between overlapping
corrugations (detail), for Greca profile.
copertura angolare
metallica superiore
150 X 150 X 0.6mm
copertura angolare
metallica inferiore
100 X 100 X 1.5 mm
Coperture Angolari
Profilo Omega
Trave di sostegno Supporto a Omega
SUNTUF® Plus
Sigillatura corrugata
SUNTUF® Plus SUNTUF® Plus
SUNTUF® Plus SUNTUF® Plus
copertura angolare
metallica superiore
150 X 150 X 0.6mm
copertura angolare
metallica inferiore
100 X 100 X 1.5 mm
Coperture Angolari
Profilo Omega
Trave di sostegno Supporto a Omega
SUNTUF® Plus
Sigillatura corrugata
SUNTUF® Plus SUNTUF® Plus
SUNTUF® Plus SUNTUF® Plus