Q-See QT17DVR4C User Manual
Page 11
-e9-
LCD WITH BUILT-IN DVR USER MANUAL
LCD WITH BUILT-IN DVR USER MANUAL
-e14-
3.3.4
Work Setup
The content of the Work Set order includes scheduling recording for each channel and the setting
up of area for each channel for motion detection.
The specific operation of each function is given below:
A.
B.
Setting the recording time:
Survey area setting:
Press Setup for each channel under "Schedule" to setup the day
(Mon-Sun), Time of recording Ist Segment, recording mode(Time, Alarm or motion) Time
of recording 2nd Segment, type of recording mode. There are 2 segments of recording to
accommodate the change in date. For example, if you start recording at 11:30pm on Monday,
the Ist set will be 11:30pm to 11:59pm and the second set will be 12:00am to 11:
The picture above is showing that the whole screen is composed
192 small areas. The
represents the area that has not
selected; the
represents the area that has been selected;
he operating method is once getting into
the setting interface; the purple small square will be flickering between two colors alternatively
which are purple and
.
The small purple square will change its color to two colors which are purple
and
and it will be flickering alternatively.
of
been purple
blue color
blue
If you press [Enter]
blue
blue color
been
t
Other function buttons
【POWER/ON】Button
【LOG IN/LOCK】Button：
【PLAYBACK】Button：
【QUAD】Button：
【ANALOG】Button：
【+】
【-】
【EXIT】Button：
【CF】Button：
【LANGUAGE】Button：
【NET】Button：
【RECORD】Button：
【STOP】Button：
【recording】
【SETUP】Button：
【F1】Button：
【F2】Button：
Press【Zoom+】、【Zoom-】Button：
Press【Aperture+】、【Aperture-】Button：
Press【Focus+】、【Focus-】Button：
Press【Assistant】Button：
Press【Auto】Button：
Press【Event】Button：
Press【Preset】Button：
【F2】
【Exit】
【F3】Button：
【F4】Button：
Operating ways：
【F4】
：for turning on and off the machine（Standby and start）；
get the operating rights, to type in the password and lock operation；
For switching pictures
built-in quad, dual views and single picture；
: Channel1
Channel 2
Channel 3
Channel 4
Dual views
(Channel 1-Channel 2)
Dual views (Channel3-Channel 4)
Built-in
quad
Channel 1
display the brightness, contrast, colour and tint, adjusting its parameters
together with the adjustment of
、
button（This operation need
to be
and this channel should be
under non-recording state）；
Exit button， exit from the operating menu to last selected menu directly.
Enter into the standby menu for recording material, copy the material in hard disk
to the outward connected memory
（hardware with CF card connector
is needed）
Enter into language selection menu directly to setup the language.
Standby button；
Stop the manual recording（operating way is the same with that for
button）；
When login the system normally, press this function button to enter into the
menu setting of the system；
For pick time play on the recorded pictures；
Press this button to enter into the control menu of platform when under the single
channel picture.
Press left, right, up and down buttons can do
adjustment to platform camera；
Adjust the distance of the picture；
Adjust the brightness of the picture；
Adjust the sharpness of the picture；
Control on some assistant switch；
Control automatically；
standby button in control of platform；
Preset control on platform, standby button；
Press again the
button or
button to exit the
setting for the platform control menu;
Standby Button.
switch between the monitor and VGA output；
Press
button in remote control unit to switch between
output of monitor and output of display when under monitoring. Its order is: output
of monitor
VGA 1
VGA 2
VGA 3；There are three states for VGA output,
which can be
for different VGA standard.
Order of Display
only when under single picture
For reviewing the recording, log, state of hard disc,information of
software edition and so on;
between
performed
mode
device
Start the manual recording in single, dual or quad mode
''
''
recording
adopted
⑤
e).
f).
Delay the alarm output:
I/O alarm output:
Under the alarm recording mode, the system is communicating the
alarm output signal with the alarm output end point automatically after moving the testing
signal has received the alarm signal from the I/O. Delay the alarm output means delaying the
continuous time of the alarm's output signal.
Two choices are open or close. When system has received the alarm signal
from the I/O, it will alarm from the output end point. When system has not received the alarm
signal from the I/O, it will not alarm from the output end point.
g).Motion alarm output the same as the above.
If you do not do the setting for each channel, it means invalid channel and that channel can't record
video, you can till see the image under monitoring if the channel has image signal But the system will
not prompt the alarm message if the image signal of this TV screen is lost.
Record Setup
Channel
Schedule
Area-Set
1
Setup
Setup
2
3
4
Return
Setup
Setup
Setup
Setup
Setup
Setup
PDF created with pdfFactory trial versi