Assembly instructions, Depth stake installation – MTD 406 User Manual
Page 3
Attention! The text in this document has been recognized automatically. To view the original document, you can use the "Original mode".
FIGURE 1.
ASSEMBLY INSTRUCTIONS
IMPORTANT:
This unit is shipped WITHOUT GASO
LINE or OIL. After assembly, see separate engine
manual for proper fuel and engine oil recommenda
tions.
NOTE:
Left
and
right
is
determined
from
the
opera
tor’s position, standing behind the tiller.
-Contents of Hardware Pack: (See Figure 1)
(Part numbers are shown in parentheses.)
Hex Bolt 3/8-16
X
3/4" Long (710-0216)
Flat Washer 3/8" I.D. (736-0117)
Ball Knob (720-0165)
Clevis Pin (711-0415)
Hairpin Cotter (714-0149B)
Hex Bolts 3/8-16
X
1.0" Long (710-0253)
Belleville Washers 3/8" I.D. (736-0105)
Lock Washers 3/8" I.D. (736-0169)
Hex Nuts 3/8-16 Thread (712-0798)
Cable Ties (725-0157)
Carriage Bolts 5/16-18 x 1.75" Long
(710-0458)
Lock Washers 5/16" I.D. (736-0119)
Hex Nuts 5/16-18 Thread (712-0267)
Belleville Washers 5/16" I.D. (736-0242)
Hex Nuts 5/16-18 Thread (712-0267)
Hex Bolt 1/4-28 x .75" Long (710-0412)
Hex Lock Nut 1/4-28 Thread (712-0117)
Rubber Washer (735-0126)
Flat Washer 5/16" I.D. x 7/8" O.D. (736-0159)
Hex Lock Nut 5/16-18 Thread (712-0158)
Reverse Drive Clutch Lever (Not Shown—
747-0517, Grip—720-0143)
Self-Tapping Screw (710-0779A)
-Loose Parts in Carton: (See figure 2)
(Part numbers are shown in parentheses.)
AA (1) Handle—R.H. (749-0642A)
Side Shields (15390)
Handle Panel (784-0271)
Depth Stake Assembly (14992)
Handle—L.H. (749-0643A)
1. Remove tiller, loose parts and hardware pack
from carton. Make certain all parts and literature
have been removed from the carton before the
carton is discarded.
2
. Extend the control cables attached to the tiller
and place on the floor. Be careful not to bend or
kink the cables.
DEPTH STAKE INSTALLATION
1. Raise the tine shield hinge flap assembly. Insert
the depth stake assembly (AD) between the two
shoulder bolts and up through the tine shield
i----- assembly as shown in figure 3. Depth stake
points toward the rear of the unit.
NOTE:
For
clarity,
figure
3
was
taken
with
tiller
raised
on end. It is not necessary to raise the tiller.
A
(1)
B
(1)
C
(1)
D
(1)
E
(1)
F
(4)
G
(4)
H
(4)
I
(4)
L
(2)
M
(4)
N
(4)
O
(4)
P
(4)
Q
(4)
R
(1)
S
(1)
T
(1)
u
(1)
V
(1)
w
(1)
X
(1)
AB
AC
AD
AE
(
2
)
(
1
)
(
1
)
(
1
)