Troy-Bilt 12087-7HP - Manual (Page 5)

MODELS 12068, 12069, 12070, 12071, 12087, 12087C, 12088, 12088C, 12089, 120890,12090, 12090C
REF
No. PART
No. DESCRIPTION QTY.
REF
No. PART
No. DESCRIPTION QTY.
WHEEL SPEED LEVER 30 1034 Bar-engine mounting...................... 2
1 9362 Pin-spring, 1/8"............................ . 1 31 9147 Plug-thread protector, red plastic.... 2
2 9838 Nut-castle (slotted), 1/2"-20......... . 1 32 9572 Bolt-hex hd., 5/16-24x1-1/8".......... 4
3 9934 Washer-shoulder, 1/2".................. . 1 33 1100242 Lockwasher-spring lock, 5/16"........ 6
4 9932 Washer-disc spring....................... . 2 34 2565 Mount-engine to tiller..................... 1
5 2628 Lever-wheel speed shift (incl. 35
*
7FIP Briggs & Stratton Engine-
Ref No.’s 6 and 18)................... . 1 Recoil or electric start. (Electric
6 1902240 Knob-wheel speed shift lever........ . 1 start requires key switch
7 9317 Pin-cotter, 3/32" X 1"................... . 1 starting system.)........................ 1
8 1231 Rod-connecting rod, wheel speed 35
*
8FIP Briggs & Stratton Engine-.......
shift lever................................. . 1 Recoil or electric start. (Electric
9 1033 Swivel-connecting rod.................. . 1 start requires key switch
10 9902 Washer-flat, 5/16", S.A.E.............. . 1 starting system.)........................ 1
11 9338 Pin-hair cotter.............................. . 1 37 8FIP Kohler Magnum Engine- recoil
12 1110107 Locknut-hex hd., 5/16“-18............ . 1 start.......................................... 1
13 1100046 Bolt-flanged hex hd., 3/8-16x1"... . 5 37 8FIP Kohler Magnum Engine-
14 1100243 Lockwasher-spring lock, 3/8”........ . 5 electric start. Requires key switch
15 9904 Washer-flat, 3/8", S.A.E................ . 7 starting system.......................... 1
16 This Ref. No. not used.................. 38A 1909064001 Muffler Guard.................................. 1
17 1113-1 Bushing-spacer, 19/64" (.300"lg.).. . 4 38B 1904565 Decal-hot surface safety warning.... 2
18 9120 Ring-retaining (tolerance ring)...... . 1 39 1900767 Decal-engine stabilization, for
BELT DRIVE SYSTEM
40 2522
Kohler engines...........................
Engine Weight-for Briggs
1
19 1920 Block- belt adjustment, 3-7/8" (incl
Ref. No.’s 13,15, and 20).......... . 1
41 1111607
& Stratton engines only..............
Bolt-hex hd., 5/16-18x2-1/4",
1
20 2100 Rod- belt adjust., 7" with
Grade 5..................................... 2
measuring gauge...................... . 1
42 20553 Spacer-zinc plated......................... 2
21 1900766 Decal- engine stabilization, for
Briggs & Stratton engines.......... WHEEL & TIRE ASSEMBLIES
22 1100011 Bolt-hex hd., 3/8-24x1-1/2".......... . 1 43 9322 Pin- roll, 5/16" X 1-1/2".................. 2
23 1919 Disc-reverse, (incl. Ref. No. 19).... . 1 45 2709-01 **Wheel & Tire Assy- bar tread.
24 9245 Belt-forward drive (no substitute left side, 4:80 x 8" tubeless tire
due to extra strength required)... . 1 with valve stem, on one-piece
25 1483 Pulley-engine power take off........ . 1 steel wheel................................ 1
26 1138-1 Shim-engine pulley, 1/16" As Req'd 45A 2709-02 **Wheel & Tire Assy-bar tread,
26 1138-2 Shim-as above, 1/32" As Req'd right side. Same as above but
27 9303 Key-engine pulley, 3/16"sq. x 2-1/2 1 for right side of tiller................... 1
46 1902020 Cap-wheel hub.............................. 2
ENGINES AND ENGINE MOUNT
28 1100045 Bolt-hex hd., 5/16-18 x 1", Grade 5.... . 2
29 1186230 Nut-hex, 5/16"-18........................ . 4
Contact an authorized Troy-Bilt dealer or the Factory for replacement engine Information.
Contact an authorized engine dealer for engine service or parts. Refer to the engine name­
plate for engine model and type information.
For correct traction and directional control, Bar Tread Tires should be mounted on the
tiller so the closed end of the “V” In the tire tread on top of the tire faces forward.