Sears 315.17506 - Manual (Page 3)

RULES FOR SAFE OPERATION
A
WARNING:
Do not attennpt to operate this tool until you have
read
thoroughly and understand completely all
instructions, safety rules, etc. contained in this
manual. Failure to comply can result in accidents
involving fire, electric shock, or serious personal
injury. Save owner's manual and review frequently
for continuing safe operation, and instructing others
who may use this tool.
,
READ ALL INSTRUCTIONS
1. KNOW YOUR POWER TOOL.
Read owner's
manual carefully. Learn its applications and
limitations as well as the specific potential hazards
related to this tool.
2. GUARD AGAINST ELECTRICAL SHOCK by
preventing body contact with grounded surfaces.
For example: Pipes, radiators, ranges, refrigerator
enclosures.
3. KEEP GUARDS IN PLACE
and
in
working order.
4.
KEEP WORK AREA CLEAN.
Cluttered areas
and benches invite accidents.
5.
AVOID DANGEROUS ENVIRONMENT.
Don't
use power tool in damp or wet locations or expose
to rain. Keep work area well lit.
6.
KEEP CHILDREN AND VISITORS AWAY.
All
visitors should wear safety glasses and be kept
a safe distance from worf< area. Do not let
visitors contact tool or extension cord.
7.
STORE IDLE TOOLS.
When not in use tools
should be stored in a dry and high or locked-up
place - out of the reach of children.
8.
DON'T FORCE TOOL.
It will do the job better
and safer at the rate for which it was designed.
9. USE RIGHT TOOL.
Don't force small tool or
attachment to do the job of a heavy duty tool.
Don't use tool for purpose not intended - for
example - A circular saw should never be used
for cutting tree limbs or logs.
10. WEAR PROPER APPAREL.
Do not wear loose
clothing or jewelry that can get caught in tool's
moving parts and cause personal injury. Rubber
gloves and non-skid footwear are recommended
when working outdoors. Wear protective hair
covering to contain long hair and keep it from
being drawn into nearby air vents.
A
WARNING:
The double insulated system is intended to protect the
user from shock resulting from a break in the tool's
internal wiring. Observe all norma! safety precautions
related to avoiding electrical shock.
11
. ALWAYS WEAR SAFETY GLASSES.
Everyday
eyeglasses have only impact-resistant lenses:
they are
NOT
safety glasses. '
12.
PROTECT YOUR LUNGS.
Wear a face or dust
mask if operation is dusty.
13.
PROTECT YOUR HEARING.
Wear hearing
protection during extended periods of operation.
14.
DON'T ABUSE CORD.
Never carry tool by cord
or yank it to disconnect from receptacle. Keep
cord from heat, oil and sharp edges.
15.
SECURE WORK.
Use clamps or a vise to hold
work. Both hands are needed to operate the tool.
16.
DON'T OVERREACH.
Keep proper footing and
balance at all times. Do not use on a ladder or
unstable support.
17.
MAINTAIN TOOLS WITH CARE.
Keep tools
sharp at all times, and clean for best and safest
performance. Follow instructions for lubricating
and changing accessories.
1
8. DISCONNECT TOOLS.
When not in use, before
servicing, or when changing attachments, blades,
bits, cutters, etc., ail tools should be disconnected
from power supply.
19. REMOVE ADJUSTING KEYS AND WRENCHES.
Form habit of checking to see that keys and
adjusting wrenches are’removed from tool be­
fore turning it on.
20.
AVOID ACCIDENTAL STARTING.
Don't carry
plugged-in tools with finger on switch. Be sure
switch is off when plugging in.
21.
MAKE SURE YOUR EXTENSION CORD IS IN
GOOD CONDITION.
When using an extension
cord, be sure to use one heavy enough to carry the
currentyourproduct will draw. An undersized cord
will cause a drop in line voltage resulting in loss of
power and overheating. A wire gage size (A.W.G.)
of at least 14 is recommended for an extension
cord 100 feet or less in length. A cord exceeding
100 feet is not recommended. If in doubt, use the
next heavier gage. The smaller the gage number,
the heavier the cord.
Page 3