TeeJet CenterLine 220 User Guide User Manual

Centerline 220 setup and operations, Setting initial guideline (continued), Guidance mode

SETTING INITIAL GUIDELINE (CONTINUED)

If the Mark A button was pressed inadvertently

and a Point A was created, it can be released by
pressing the Mark A-B button followed by the
Decrease button.

GUIDANCE MODE

Press the Guidance Mode button to select Straight

or Curved A-B Guidance. View the bottom left of the

display window to see the Guidance mode selected.

STrAIGhT A-B MODE

provides straight line

guidance between two reference points (Points A

and B).

CUrVED A/B MODE

provides curved guidance

between two reference points (Points A and B). All

swaths are identical to the path driven on the first
pass between Points A and B.

A+ NUDGE FEATUrE

At any time after a guideline is created, the guidance line can be
shifted to the current vehicle position by pressing the Mark A-B
button followed by the Increase button. The heading (and shape,

if in Curved Guidance mode) of the original guideline is maintained,

but the A-B line is shifted to the vehicle’s present location.

INSTALLATION

The CenterLine

220 is equipped with three cables: the attached

Power/GPS Speed cable, the Antenna cable, and the Power Adapter

cable.

POwEr/GPS SPEED CABLE - The CL220 should be connected

to a clean cigarette lighter receptacle for power. As an option, the

CL220 can be connected to any controller or monitor that supports a

radar speed input. when connected to the radar speed input of the

monitor or controller, the CL220 will be powered by the controller and

will provide a radar-like speed signal to that device.

GPS ANTENNA AND CABLE - The antenna is magnetic, so for metal

vehicles, position the antenna in the center of the vehicle at the high-

est point. For non-metal vehicles, a metal plate with adhesive strips

has been included in the kit for easy mounting and installation. It is

STrONGLY recommended to use this metal plate underneath the

antenna as it will also boost signal strength. Once the antenna has

been positioned, route the antenna cable carefully to avoid damage.

Attach it to the threaded connector on the back of the CL220.

- Connect to cigarette lighter

with the power adapter cable.

- Connect directly to radar speed

input of a compatible controller

(refer to CL220 Providing Speed Signal

on reverse)

Press suction cup to mounting surface and ro-

tate locking arms clockwise to the ON position.

Press the Power button to power up the CL220. The CL220 start-

up screen will appear until a GPS signal is acquired. Press the Power

button again to power down the console.

BrIGhTNESS/CONTrAST

Press the Brightness or Contrast buttons.
Use the Increase and Decrease

buttons

to make adjustments. To invert the colors on the

display, press and hold the Contrast button for

3 seconds.

SwATh wIDTh

Press the Swath width button. Use the In-
crease and Decrease

buttons to make ad-

justments to the swath width.

The swath width value is displayed in feet. The

swath width measurement displayed will be used

until changed.

SETTING ThE INITIAL GUIDELINE

At the desired location for guidance to begin,
press the Mark A-B

button. Point A will be

marked. The display will then change to Mark B.

Travel to the location for Point B to be marked.
Press the Mark A-B button to mark Point B.

The CL220 will begin providing guidance with the

lightbar and data display.

Point

ChANGE PAGE

Use the Change Page button to alternate be-

tween the Data Page and the Map Page.

rETUrN TO POINT

Press the return To Point button to store a loca-

tion in which to return at a later time. A dot will ap-

pear on the bottom of the display, indicating that a

position has been stored.

To locate the point, press the return To Point

button again and begin navigating toward the point

as indicated on the display. To exit return To Point,
press the return To Point button again. Use the

Change Page button to switch between the re-

turn To Point display screens.

Data Page

Map Page

The dashed lines

represent

adjacent swaths

The arrow points in

the direction of the

marked point

A line is drawn between

the marked point and the

vehicle

The vehicle is at the

marked point location

Position the GPS antenna in the center

of the vehicle at the highest point with

a clear view of the sky. If the tractor is

non-metal, mount the metal plate in the

center of the vehicle at the highest point

with the adhesive strips and place the

antenna on the plate. route the antenna

cable carefully to avoid damage.

Point

Straight A-B Guidance

Curved A-B Guidance

Speed/Power

Cable

Connect to

+12v Only

Power Cable

45-05478

+12v Only

Power Cable

45-05458

DC:xx/xx/xx

POWER CABLE

45-05471

DC: XXXX

Vecro

Strips

60-10081

Antenna Mounting

Plate

65-05179

GPS Antenna

GPS Speed/Power Cable

45-05478 Cable, Battery Power

45-05471 Cable, Adapter Weather-Pack

*45-05458 Cable, Lighter Adapter

*included in kit 90-02399

Antenna

Metal plate

CENTErLINE 220 SETUP AND OPErATIONS

GPS

DGPS

5.8 MPH

Power

Lightbar

Brightness

Contrast

GPS Status

Lights

Change

Page

Display

Increase/

Decrease
Guidance

Mode

Swath width

return to

Point

Mark A/B

guidance mode selected

GPS

DGPS

GPS

DGPS

GPS

DGPS

lights illuminated on the right of the

lightbar require a steering adjust-

ment to the left

lights illuminated on the left of the

lightbar require a steering adjust-

ment to the right

Center

3.0 ft (.9 m)

4.5 ft (1.4 m)

6.0 ft (1.8 m)

7.5 ft (2.3 m)

1.5 ft (.45 m)

Distance to point