SilentKnight SK-Relay-6 Addressable Six Relay Module User Manual

Page 3

wIRING
NOTE: All wiring must conform to applicable local codes, ordinances, and
regulations.
1. Install module wiring in accordance with the job drawings and appropri-

ate wiring diagrams.

2. Make electrical connections by stripping approximately 1/4˝ (6.35mm)

of insulation from the end of the wire sliding the bare end of the wire
under the clamping plate, and tightening the clamping plate screw.

3. Set the address on the modules per the job drawing. Use the rotary code

switches to set the address of the first module between 01 and 94 (or 01
and 154 for panels that support 159 addresses). The remaining modules
are automatically assigned to the next five higher addresses. For exam-
ple, if the base address switch is set to 28, the next five modules will be
addressed to 29, 30, 31, 32, and 33. DO NOT set the lowest address above
94(or 154 for panels that support 159 addresses), as the other modules
will be assigned to nonexistent addresses.

4. A shunt is provided to disable a maximum of three unused modules.

Modules are disabled from the highest address and work downward. If
two modules are disabled, the lowest four addresses will be functional,
while the highest two will be disabled. For example, if the shunt for Ad-
dress Disable is placed on “two” and the base address switch is set to 28,
the modules will be assigned to 28, 29, 30 and 31.

NOTE: The SK-Relay-6 must have power cycled for shunt changes to take
effect.

5 6

7 8 9

7 8

910

N.C.

N.O.

COMMON ADDRESS

N.C.

N.O.

COMMON ADDRESS

N.C.

N.O.

COMMON ADDRESS

N.C.

N.O.

COMMON ADDRESS

N.C.

N.O.

COMMON ADDRESS

N.C.

N.O.

COMMON ADDRESS

– +

–

SLC

BASE ADDRESS

ADDRESS

DISABLE

NONE

ONE

TWO

THREE

6.8"

5.8"

FROM PANEL

OR PREVIOUS DEVICE

SIGNAL LINE CIRCUIT (SLC)

32 VDC MAX.

SEE PANEL INSTRUCTION

MANUAL FOR

WIRE REQUIREMENTS

TO NEXT

DEVICE

–

COMMON

RELAY CONNECTIONS

STATUS

INDICATORS

C0250-04

FIGURE 5: wIRING AND PROGRAMMING ThE SK-RELAY-6 MODULE

FCC STATEMENT

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used
in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular instal-
lation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:

– Reorient or relocate the receiving antenna.

– Increase the separation between the equipment and receiver.

– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

– Consult the dealer or an experienced radio/TV technician for help.

NOTES:

The relay contacts on the SK-Relay-6 may be connected to either a

•

power-limited or non power-limited source, this wiring must remain
separated by at least 1/4˝ (6.35 mm) from all power-limited wiring.

Power-limited circuits must employ type FPL, FPLR, or FPLP cable as

•

required by Article 760 of the NEC.

For easier wiring, assign all power-limited wiring to one side rather than

•

alternating with non power-limited.

PROGRAMMING
The modules are programmed as modules in each system according to the
programming instructions in the appropriate FACP manual.

SK-460-007

I56-3439-000