beautypg.com

Coleman WEATHERMASTER 8 TENT MODEL 2000001596STITCHLINE User Manual

Weathermaster, 8 tent, Before you begin

background image

WEATHERMASTER

®

8 TENT

MODEL 2000001596

STITCH LINE

Fig. 1

To Set Up Tent

1. Unfold tent and spread out on a clean, level surface with the

door facing the desired direction. Unzip doors. (Fig. 1)

4. Assemble six, steel, shock-corded,

Leg Poles. Push down on steel button
on tapered end and insert into end
with four holes.
NOTE: Make sure steel button locks
into third hole on pole as shown. (Fig.4)

5. Insert curved end of Leg

Poles (with red dot) into
the ends of the RidgePole
(with red dot). Insert
curved end of remaining
short Leg Poles into the
ends of the remaining
Ridge Poles. (Fig. 5 & 6)

6. Rotate all six Leg Poles upright and insert

pin on each web loop at the side locations
as shown. (Fig. 7 & 7A)

(continued on other side)

Pole Descriptions

Pole

Pole

Pole

Description

Qty.

Dia.

Repair Kit

Replacement Kit

Long Leg Pole, steel

(w/ red marking)

2

19mm

N/A

5010000612

Short Leg Pole, steel

4

19mm

N/A

5010000622

Curved Ridge Pole, steel

(w/ red marking)

1

19mm

N/A

5010000617

Curved Ridge Pole, steel

2

19mm

N/A

5010000616

Window Vent Pole,

black, fiberglass

2

8.5mm 5010000541

5010000547

Door

Ridge Pole with

Red Marking

Button in third hole

Fig. 4

Fig. 5

Fig. 6

Fig. 2

Sleeve

with Red

Trim

Curved End of

Long Leg Pole

2. Pull four corners of tent taut, then secure

by driving stakes through web loops at an
angle for better anchoring. (Fig. 2)

Ridge Pole

with Red

Marking

Fig. 3

Sleeve

with Red

Trim

3. Assemble three, steel, shock-corded,

curved Ridge Poles. Insert Ridge Pole
(with red marking) into center sleeve
on top of tent with the red trim (Fig. 3).
Insert the remaining curved Ridge Poles
into the other two sleeves on top of tent.

Fig. 7

7A

Pin

6. Assemble the two, shock-corded, black Window Poles,

then insert one into sleeve located at each end of tent.
(Fig. 7 & 7B)

7. Insert tapered metal tip on Window Pole into Leg Pole.

NOTE: It may be necessary to gently rotate Leg Pole so the
hole will line up with the Window Pole.

8. Go to opposite end of each window pole and gradually apply

pressure to the pole forming an arch. Insert the pin into the
leg pole end at the corners of tent. (Fig. 7 & 7C)

9. Locate the plastic hooks at sides and corners of tent, then

snap onto Leg Poles to attach. (Fig. 8)

10. Locate web strap

with plastic hook on
the sides of each
end panel Window
Vent, then snap onto
the corner Leg Pole.
(Fig. 9)

7C

Metal Tip

7B

Sleeve

Window Pole

Hole in

Leg Pole

12. Insert plastic stakes through

web straps located on both sides
of tent, then drive in to secure.
(Fig. 11)

Fig. 11

11. To stretch tent to finished size:

• Push in button on Leg Pole while

twisting lower Leg Pole section
counterclockwise (Fig.10);

• Pull up on top Leg Pole section

until tent is taut;

• Twist the lower Leg Pole clock-

wise until the button locks into
the center or lowest hole;

• Repeat on remaining Leg Poles.

Fig. 9

Window Vent

Web Tent Strap

Corner

Leg Pole

Fig. 8

Fig. 10

Button

Center Hole

Lower Hole

Lower
Leg Pole
Section

Upper
Leg Pole
Section

Before you begin

Read all instructions before set up.
• Select a level site clear of rocks, branches, and other hard or

sharp objects, to install your tent.

WARNING: Keep clear of overhead power lines.

• Do not set up your tent under trees because of potential

lightning strikes or falling tree limbs in inclement weather.

• Secure with all stakes and guylines provided to prevent

property damage or personal injury.

• For best results in windy conditions, position narrow end of

tent into the wind.

• Enlist the help of at least one other person to assist you when

it is time to assemble the tent.