Philips PR1909B - Manual (Page 4)

H owto S et U p and U se your TV
o M enu |—tBEGINJ
■
F irst T ime S etup
F irstTime Setup takes care of
some basic TV settings for you.
Follow these steps:
• to set the language of the TV’s
on-screen menu, and
• to quickly add area channels
into the TV’s memory.
Press the POWER
button to turn ON the TV.
The language selection menu
appears on the TV screen.
/ SELECT LANGUAGE ^
> ENGUSH ON
ESPAÑOL
SELECT AT OR
PRESS MENU TO CONTINUE
Press the CH(annel) AfW
buttons to select English or
Spanish menus. Then, press the
MENU button.
'CONNECT ANTENNA OR CABLE
TO TV
THEN PRESS ►
TO END PRESS EXIT
,
Press theVOL(ume) ^ but­
ton to begin automatic channel
setup.
When setup is complete, “CHAN­
NELS ARE SET” will appear on
the screen.
If you do not g
want to set up
channels now, press
the STATUS/EXIT
button.
The menu shown at
step I will appear
only the first time you
turn on the TV. If it
does not appear, fol­
low the instructions
on page 5 to select a
language and set up
channels.
If you have not con­
nected the antenna or
cable to the TV, an on­
screen message will
prompt you to do so.
You may need to fol­
low the steps for
Automatic Channel
Setup on page 5 in
order to finish setting
the channels available
jnjjour^reau^^^^^^
rCB R emote
T ' 0 load the batteries into the
remote:
I. Slide off the battery
compartment lid on the
remote control.
2. Insert two AA batter­
ies (supplied) into the
battery compartment
as indicated inside the
compartment. Batteries
installed incorrectly may
damage the remote con­
trol.
3. Replace the lid.
Battery
Compartment
Lid
Battery
Compartment
Point the remote control
toward the remote sensor on the TV
when operating the TV with the
remote.
Press to access the on-screen menu.
Press the CH(annel) AIW buttons to
select an item in the menu. Press the
VOL(ume) ►/◄ buttons to adjust an
item in the menu or to advance to the
next menu.
Number Buttons
Press to select channels.
• Cable Users
Enter channel numbers as a two-digit
number for the quickest results. For
example, to select channel 6, press 0,6. If
you only press the Number 6 button,
channel 6 will be selected after a brief
delay. (There also may be a brief delay
when you select channels 10, 11, and
12.) If you want to select channels 100
and above, enter channel numbers as a
three-digit number. For example, to
select channel 117, press 1, 1,7.
• Antenna Users
Enter channel numbers as a two-digit
number for the quickest results.You may
only select channels 2-69. For example,
to select channel 5, press 0,5. If you only
press the Number 5 button, channel 5
will be selected after a brief delay.
SLEEP Button
Press to set the TV to turn itself OFF
automatically. Details are on page 6.
CHfanneh AIT Buttons
Press to scan through programmed
channel numbers. Press to select an item
in the on-screen menu.
VOLfume'> Buttons
Press to adjust the TV sound level. Press
to adjust an item in the on-screen menu,
to advance to the next menu, or to
return to a previous menu.
MUTE Button
Press to turn OFF the sound on the TV.
Press again to return the sound to its
previous level.
STATUS/EXIT Button
Press to see the current channel number
on the TV screen.
Press to remove the on-screen menu.You
also may remove the menu by pressing
the CH(annel) A/T buttons to select
EXIT, then pressing theVOL(ume) ► but­
ton.
ALT. CH /Alternate Channel^
Button
Press to return to the TV channel you
were viewing immediately before switch­
ing to your current channel.
o
T elevision I—CHoiB)
1^ Press the POWER
button to turn ON the TV.
Be sure to connect the TV
power cord to a standard AC
outlet.
Note:
You can connect earphones (not supplied) to the EARPHONE
jack on the front of the TV for private, personal listening.
Press the VOLUME
A/T buttons to adjust
the sound level.
Press the CHAN­
NEL A/T buttons to
select TV channels.
Remote
Sensor
Press the MENU button
to display the TV’s on-screen menu.
Press the CHANNEL A/T
buttons to select an item in the
menu.
Press the VOLUME A/T but­
tons to adjust an item in the
menu or to advance to the next
menu.
Note: To remove the menu, press
the CHANNEL A/T buttons to
select EXIT.Then, press the VOL­
UME A button.
The current
channel number
will appear briefly
when the TV is first
turned ON and with
channel changes.To
display the channel
number for five sec­
onds, press the STA­
TUS/EXIT button. Or,
to remove the chan­
nel number, press the
STATUS/EXIT button
again.
■ 4-