Lo-z – Milwaukee Tool 2206-20 User Manual

Page 3

Dial Position

Range

Resolution

Accuracy

Voltage AC/DC

400V

1000V

0.1V/1V

: ±(1.5% + 5 dgt) 45-500 Hz

: ±(1.0% + 2 dgt)

Current AC

200A

0.1A

±(3.0% + 3 dgt) 45-60 Hz

Resistance

Continuity

400.0Ω

4.000kΩ
40.00kΩ
400.0kΩ

4.000MΩ
40.00MΩ

0.1Ω

0.001kΩ

0.01kΩ

0.1kΩ

0.001MΩ

0.01MΩ

±(1.0% + 5 dgt)
±(1.0% + 2 dgt)
±(1.0% + 2 dgt)
±(1.0% + 2 dgt)
±(1.0% + 2 dgt)
±(2.0% + 5 dgt)

Capacitance (2206-20)

1000μF

1μF

±(1.9% + 2 dgt)

100.0μF

0.1μF

Current DC (2206-20)

400.0μA

1000μA

0.1μA

±(1.0% + 2 dgt)

Temperature C° / F°
(2206-20)

-40ºC ~ 400ºC

-40ºF ~ 752ºF

0.1°C

0.2°F

C°:±(1% + 2C°)
F°:±(1% + 3 F°)

Lo-Z

Low Input Impedance
(2205-20)

400.0V

1000V

0.1V/1V

±(2.0% + 3 dgt) AC:45~500Hz

Functions

FUNCTIONAL DESCRIPTION

1. Light On/Off button
2. Hold button
3. Jaws
4. Light
5. NCV indicator
6. Dial
7. Display
8. Terminal inputs

Cat. No.
2206-20

Lo-Z

Cat. No.
2205-20

ASSEMBLY

Selecting C° or F°
1. Turn Rotary Dial to OFF and

disconnect the test leads.

2. Unscrew and remove bat-

tery door and remove any
installed batteries.

3. Set the C°/F° switch to the

desired position.

4. Replace batteries according

to “Loading/Changing the Batteries.

5. Close the battery door and tighten screw se-

curely.

Loading/Changing the Batteries
Replace batteries when the Low
Battery indicator is displayed.
1. Turn Rotary Dial to OFF and discon-

nect the test leads.

2. Unscrew and remove battery door.
3. Insert two (2) AA batteries, according

to the polarity marked in the battery
compartment

4. Close the battery door and tighten screw

securely.

WARNING

To avoid an electrical hazard, turn the Rotary
Dial to OFF and disconnect the test leads
before opening battery compartment or
replacing batteries.

OPERATION

Before Use
Confi rm the Rotary Dial is set to the correct position,
the instrument is set to the correct measurement
mode, and the Data hold function is disabled. Oth-
erwise, desired measurement cannot be made.

LCD Backlight
The LCD backlight will turn off after about 3 minutes
of inactivity. Push any button or turn the rotary dial
to turn the backlight on.

Making a Measurement

Voltage

DANGER

To avoid electrical shock:
Never make measurement on a circuit in
which voltage over AC 1000V or DC 1000V
exists.
Do not use with the Battery Cover removed.
Keep fi ngers behind the guards and away
from test lead tips during measurements.

1. Set the Dial to

posi-

tion.

2. Connect the red test lead

to the VΩ terminal and the
black test lead to the COM
terminal.

3. AC: Connect the test leads

to the circuit under test. The
reading is displayed.

DC:

Connect the red test

lead to the positive (+)
side and black test leads
to the negative (-) side of
the circuit under test. The
reading is displayed. A reversed connection is
indicated as a negative value.

Current

1. Set the Dial to

position.

2. Run the conduc-

tor through the
jaws. The read-
ing is displayed.

NOTE:

Do not

place 2 or more
wires between
jaws at the same
time. Place wire between arrows. Otherwise,
irregular results will occur.

CAUTION

Maximum conductor size is approx 5/8”
diameter.

DANGER

To avoid electrical shock:

Never make measurement on a circuit in
which voltage over AC 1000V or DC 1000V
exists. Jaws are designed not to short the
circuit under test. If equipment under test has
exposed conductive parts, however, extra
precaution should be taken to minimize the
possibility of shorting.

Do not use with the Battery Cover removed.

Disconnect the test leads from the instrument
for current measurement.

Correct

Incorrect

Lo-Z

Low Input Impedance

(Cat. No. 2205-20 only)
Automatic voltage detection
(AC or DC).
1. Set the Dial to