Philips AW 7720/00 - Manual (Page 5)

English
• When monitoring during recording, adjust the
sound with the controls VOLUME, BALANCE, GRA-
PHIC.EQUALIZER and DYNAMIC BASS BOOST.
These controls do not affect the recording.
• For fast winding, press REWIND •« or F.FWD
To stop, press STOP/EJECT ■.
Recording from the radio
• Set the MODE selector to RADIO.
• In case of FM radio recordings, set the FM STE­
REO button to MONO or STEREO.
• A whistling sound occurring during MW radio re­
cordings can be suppressed by setting the RIF-selec-
tor to another position.
Microphone recording
• Connect the microphone to the socket MIC MIX.
- Microphone only: set the MODE selector to TAPE.
- Mixing with CD: set MODE selector to CD/LINE IN.
- Mixing with radio: set MODE selector to RADIO.
• If a howling sound occurs:
- keep the microphone away from the speakers,
- or reduce the volume,
- or use headphones for monitoring.
Recording from the CD/LiNE IN sockets
• Connect the CD/LINE IN sockets to the output
sockets LINE OUT or REC OUT of the other set.
• Set the MODE selector to CD/LINE IN.
Starting and stopping
• Start recording by pressing RECORD •.
• For brief interruptions, press PAUSE ii. To restart
recording, press this button once more.
• To stop recording, press STOP/EJECT ■. On press­
ing again, the cassette holder will open.
• Always switch off the set after use with the
POWER button. POWER will then go out.
DUBBING - Copying from deck 2 to 1
When copying, it is recommended to use fresh batte­
ries or to connect the set to the mains supply.
• Switch on the set using the POWER button.
POWER lights up.
• Set the MODE selector to TAPE.
• Set the DUBBING button to:
NORM X for normal speed copying:
HIGH for high speed copying.
Do not switch this button during dubbing.
• Press both STOP/EJECT ■ buttons and insert a re­
corded cassette into deck 2 and a cassette which is
suited for recording into deck 1 (fig. 3).
• To start dubbing, press on deck 1 RECORD • and
on deck 2 PLAY ►.
• By pressing PAUSE li on deck 1, you can omit un-
desired passages while deck 2 continues. To restart
copying, press PAUSE II once more.
• Using PAUSE II of deck 2, deck 1 will record a
blank part.
• To stop dubbing, press both STOP/EJECT* but­
tons.
• Always switch off the set after use with the
POWER button. POWER will then go out.
CASSETTE PLAYBACK
Playback on deck 1 or 2
• Switch on the set using the POWER button.
POWER ife lights up.
• Set the MODE selector to TAPE.
• Press STOP/EJECT ■ and insert a recorded cas­
sette (fig. 3).
• Set the TAPE butto to:
Ferro X for NORMAL cassettes, lEC I.
Cr for CHROME cassettes, lEC II.
• For fast winding, press REWIND « or F.FWD
To stop, press STOP/EJECT* *.
• Adjust the sound with VOLUME, BALANCE, GRA­
PHIC EQUALIZER and DYNAMIC BASS BOOST.
• Press PLAY ► and playback will start.
• To stop, press STOP/EJECT*. On pressing again,
the cassette holder will open.
When the end of the tape is reached, the recorder
buttons are released.
• Always switch off the set after use with the
POWER button. POWER will then go out.
Continuous play
• Switch on the set using the POWER button.
POWER S’ lights up.
• Set the MODE selector to TAPE.
• Press both STOP/EJECT * buttons and insert a
recorded cassette into both decks (fig. 3).
• Press on deck 2 PLAY ► and on deck 1 PAUSE II
and PLAY ►: deck 2 will now play and deck 1 stands
still.
As soon as deck 2 stops (at the end of the cassette
or when its STOP/EJECT * button is pressed).
PAUSE II is released and deck 1 will start playing
back.
• To stop, press STOP/EJECT *.
• Always switch off the set after use with the
POWER button. POWER will then go out.
MAINTENANCE______________________________
To ensure a good recording and playback quality,
clean the parts indicated in fig. 5 after every
50 hours of operation or, on average, once a month.
• Open the cassette holder using STOP/EJECT *.
• Use a cotton bud slightly moistened with alcohol
or a special head cleaning fluid.
• Press PLAY ► and clean the rubber pressure roller
®.
• Then press PAUSE II and clean the capstan (c),
recording/playback head ® and erase head ( a ).
• After cleaning, press STOP/EJECT *.
Cleaning of the heads ( a ) and (|) can also be done by
playing a cleaning cassette through once.
- Do not expose the set, batteries and cassettes to
rain, moisture, sand, or to excessive heat e.g. from
heating equipment or in motor cars parked in the
sun.
The type plate is located on the base of the set.
This product complies with the radio interference re­
quirements of the European Community.
JC
.¡2
"o)
c
111