Philips AK 701 - Manual (Page 8)

U] PREV/NEXT: same as PREV/NEXT function of ©
and © of the CD player.
[¥] <]<1 SEARCH t>|>: same as SEARCH function of ©
and © of the CD player.
[7] PLAY/PAUSE: same function as ® of the CD
player.
[a] STOP; same function as © of the CD player.
[i] REPEAT: same function as ©of the CD player.
03 SHUFFLE; same function as © of the CD player,
[n] REVIEW: same function as © of the CD player.
Ol] PROGRAM: same function as © of the CD
player.
OPERATION
Warning
• Check that you have removed the red transit
protection clamp on the underside of the player (but
refit it during further transport).
• Always remove the CDs from the player before
moving the unit!
TO PLAY DISCS
• Switch on the CD changer using the POWER
ON/OFF switch ©.
• Press OPEN/CLOSE ® to open the CD tray @.
• Holding the disc between the thumb and fingers of
the outstretched hand, remove it from the packaging
(Rg. 3) and place it with the label uppermost in the
tray © (Rg. 5). Both standard 12 cm (5") discs and
8 cm (3") discs (CD singles) can be used.
• Use the PREFERRED POSITION in the tray, when
you insert only one disc.
• When you wish to insert more discs, press the
LOAD button © to rotate the turntable in the tray.
• Press the OPEN/CLOSE button ©to close the tray
©■
• Press the PLAY/PAUSE button ©. The CD of the
preferred position will now be played.
• To play another CD, select the desired disc
number with one of the DISC SELECT buttons ©.
Play begins automatically within a few seconds. In
display ©you can always see which disc and which
track are being played. Play will stop after the last
disc.
Important
If an E (for Error) appears in the display, the CD-player
cannot read the diso. Possible causes are:
-you inserted the CD the wrong way: the label should
face up (Rg. 5);
- the surface of the disc is badly scratched or dirty,
see ’Maintenance';
- the lens is steamed up because of a sudden
transition from a cold into a warm environment; do not
clean the lens, but let the set acclimatize for a while.
Changing discs during play
• Press OPEN/CLOSE © to open the CD tray ©.
Two discs can now be changed.
• Press the LOAD button ©to rotate the turntable in
the tray, after which the other two discs can be
changed.
Selecting a different disc during play
• Press the desired number of the DISC SELECT
buttons ©.
In display ©the disc number will appear and shortly
afterwards the first track of the chosen disc will start
to play.
Selecting a different track during play
• Press SEARCH NEXT @ (or PREV SEARCH ©)
until the required track number appears in the
display.
- Shortly after this, the chosen track vwll start playing.
Starting again with the track that is currently
playing
• Press PREV SEARCH © once.
- The track will be started again from the beginning.
Searching for a passage during play
• Hold SEARCH NEXT © or PREV SEARCH ©
pressed down to search for the required passage. If
you release the button, play will continue.
Repeating play
• During play press REPEAT © The REPEAT
indication lights up.
- All discs are played and then repeated.
• Press REPEAT again to stop the repeat function.
The REPEAT indication goes out.
- Play continues as normal.
• REPEAT can also be used during a PROGRAM,
SHUFRE, and INTROSCAN.
Introscan
The INTROSCAN function can be used in both STOP
and PLAY modes by pressing the INTROSCAN
button ®. SCAN will then appear in the display.
The INTROSCAN function causes the first few
seconds of every track of all CDs to be played (in
PLAY mode only the rema/n/ng tracks). After playing
the opening seconds of a track the CD player jumps
to the beginning of the next track. The corresponding
track number appears in the display ©.
• Pressing the PLAY/PAUSE button © cancels the
INTROSCAN function. The CD plays normally from
the current track onwards.
• If you press the SEARCH NEXT button © or the
PREV SEARCH button © the unit remains in the
INTROSCAN function and the first few seconds of the