Philips AK 701 - Manual (Page 2)

English
INSTALLATION
• In the base of the unit there is a red transit
protection clamp. This clamp serves to secure the
mechanism of the CD changer to protect it during
transport. Remove the red transit protection clamp
and store it in the hole © on the rear, see Rg. 2.
Should you wish to transport the unit again, the
mechanism must be secured once more in order to
prevent damage.
• Always remove the CDs from the tray before
• moving the unit.
• Do not cover any vents and make sure that there
is several centimetres ventilation room around the
unit.
• Do not place the unit in direct sunlight or close to
radiators, heaters, etc. This will help prevent over­
heating. Do not expose the unit to rain or moisture.
CONNECTIONS AND CONTROLS
Fig. 2
© Socket for remote control (not on all versions).
This socket can be connected to the REMO­
TE OUT or RC 5 OUT socket of another unit. An
optional cable is avaiiable under number
SBC 1103 or 4822 321 21204.
® CD OUT sockets. For connection to the CD IN or
AUX IN sockets on the amplifier.
© Hole for storing the transport clamp.
© Connection socket for mains supply cable (on
some versions a fixed cable). Connect the mains
supply cable supplied with the CD changer to this
socket.
Warning: Do not connect the player to the mains
supply without first checking that the voltage
stated on the type plate (and/or the setting of the
voltage selector © corresponds to the local
voltage. If this is notthe case, consultyour dealer.
The type plate is on the rear of the player.
© Voltage selector (not on all versions). Use a
screw driver or something similar to set the
voltage selector to the local voltage.
Important note for users in the U K.: The U K. version is not fitted with
a mams plug When fitting a mams plug to the mains lead, proceed as
iollows; The wires in the mams lead are coloured wth the followng
code:
BLUE=NEUTRAL, BROWN=LIVE. As these colours may not corre­
spond with the colour markings identifying the terminals in your plug,
proceed as follows; The Brown wire must be connected to the terminal
which is marked with the letter L or coloured Red. The Blue wire must
be connected to the terminal which is marked with the letter N or
coloured Black Do no/connecl either wire to the earth terminal in the
plug, marked by the loitor E or by iho solely earih symbol or coloured
green or green and yellow
Note This equipment must be protected byaSAmpFuse ila 13Amp
plug »s used or. i! any other type of plug is used, by a 5 Amp Fuse either
in the plug or adapter or at the dislnbulion board II m doubt, consult
a qualified eteclncian
Fig.1
o POWER ON/OFF switch
To disconnect the set from the mains completely,
withdraw the mains plug from the wall socket.
® CD tray.
® DISC SELECT buttons - for selecting the disc
number.
® Display.
© PROGRAM - for storing the tracks of a pro­
gramme.
® REVIEW - causes all the programmed track
numbers to appear in the display.
© INTROSCAN - to play the first few seconds of all
tracks of all CDs in the tray.
® PREVSEARCH
• during PLAY mode:
- press briefly to play the current track again.
When pressed briefly again the player goes to the
previous track.
- hold down for rapid backward playback.
• in the STOP position:
-press briefly to jump to the previous track
number (e.g. when programming).
© SEARCH NEXT:
• during PLAY mode:
- press briefly to jump to the next track
- hold-down for rapid search fonvard.
• in the STOP position:
- press briefly to display the next number (e.g.
when programming).
@ PLAY/PAUSE - for starting play of a track, or for
interrupting play.
© OPEN/CLOSE - for opening/closing the CD fray.
® STOP for stopping pfay. When the CD is stationa­
ry the highest track number is displayed.
© CL^R PROGRAM - tor clearing a programmed
selection, or clearing the programmed tracks of
a specific CD, when pressing the relevant DISC
SELECT button © immediately thereafter.
@ REPEAT: to continuously repeat ail CDs, a
programmed selection, or the SHUFFLE pro­
gramme. Press again to cancel the Repeat
function.
© SHUFFLE button for playing all tracks of all CDs
in a random order.
© LOAD button - to rotate the disc turntable in the
tray.
© IR - sensor for remote control (not on all versions).
© STAND BY indicator (not on all versions).
REMOTE CONTROL UNIT, Fig. 6 .
(not on all versions)
[T] STAND BY: to switch off.
IT] CLEAR: to clear a programme.
0 SCAN: same function as ® of the CD player.
[7] - DISC +: to select a disc.