Interlogix Simon XT REV B Installation Manual - Manual (Page 4)

Table 3 below shows the top menu structure. To see all of the
possible options, refer to the Simon XT Installation Manual.
7DEOH7RSPHQXVWUXFWXUH
Set clock (system time)
Enable chime
Enable special chime
Sensor test
Communication test System tests
Initiate download call
Access codes
Security
Phone #s
Phone options
Sensors
Reporting
Timers
Touchpad options
System options
Siren options
System programming
Audio verification
Revision
Contrast
7RHQWHUV\VWHPSURJUDPPLQJ
1. Scroll until the display shows System Programming, and
then press OK. The display prompts for an access code.
2. Enter the access code from the codes listed in Table 5 below.
The display shows each entered access code digit as an
asterisk.
3. Press OK. The panel is now in program mode.
1RWH Do not remove the panel power while in program mode.
7DEOH6LPRQ;7SURJUDPPLQJFRGHV
&RGH 'HVFULSWLRQ
Dealer code You can use the dealer code to program all system
functions, including high-security options that are not
accessible with the installer code if it is different from
the dealer code. Depending on how the access code
is set, the default dealer access code is 654321,
54321, 4321 (factory default), or 321. This code can
be used for all programming.
Installer code Depending on how the access code is set, the default
installer code is 654321, 54321, 4321 (factory default),
or 321. This code is limited to changing all but the
following: Dealer code, code length, downloader code,
phone lock, phone #1, phone #2, phone 1 report mode,
phone 2 report mode, HW1 function.
$FFHVVFRGHV
Table 5 below describes the Access code menu programming
options.
7DEOH$FFHVVFRGHV
)XQFWLRQ 'HIDXOW 'HVFULSWLRQ
Dealer code 4321 You can use the dealer code to program all
system options, including high-security
options that are not accessible with the
installer code if it is different from the dealer
code. Changing the dealer code to differ
from the installer code will prevent the
installer from viewing certain fields.
If you change the dealer code and enter
program mode with the installer code, the
installer should no longer be able to see the
following: code length, downloader code,
phone lock, phone #1, phone #2, phone 1
report mode, phone 2 report mode, HW1
function.
Installer code 4321 You can use the installer code to program
most installer options, except for high-
security dealer options.
Master code 1234 You can use the master code to arm/disarm
the system and to enter user programming
and bypass sensors.
User codes 1
to 8
Blank You can use the user codes to arm/disarm
the system.
Duress code Blank You can use the duress code in place of the
master or user code to cause a silent alarm.
Code length Four digits Codes can be three to six digits long.
6HQVRUV
These instructions describe how to add (learn) sensors, touchpads,
and other system devices into panel memory. The panel
recognizes a sensor when you press a sensor program button,
press and release a tamper switch, press a sensor test button, or
put a sensor into alarm. Table 6 below describes the programming
method for each device.
1RWH If you are installing a sensor on a gun case, jewelry box, or a
similar case, and the sensor is active in level one, you must
subdisarm to avoid putting the panel into alarm when the sensor
and the magnet are separated.
7DEOH'HYLFHSURJUDPPLQJ
'HYLFH 7R
SURJUDP
Door/window
sensor
Press the button on the top of the sensor (cover
removed) or trip the tamper.
Motion sensor Press the button on the back of the sensor (mounting
plate removed) or trip the tamper.
Smoke detector Trip the tamper, press the test button, remove the
detector from its base, or put the smoke detector into
alarm.
Hardwired sensor Separate the sensor from its magnet.
CO al arm
Trip the wall tamper by removing the sensor body from
the mounting plate.
4 / 8 P/N 466-2398 • REV B • ISS 09JAN13