Great Planes Sequence F3A EP ARF - GPMA1575 - Manual (Page 4)

4
If using the recommended brushless motor, a 45A brushless
ESC is required:
❏
Great Planes Silver Series 45A Brushless ESC
5V/2A (GPMM1840)
Propeller
If you are installing the recommended RimFire brushless
motor, we suggest a 12x6E APC propeller.
❏
APC 12x6 Electric Propeller (APCQ4130)
Batteries and Charger
One 2100mAh 14.8V Lithium Polymer battery pack is
recommended.
❏
Great Planes ElectriFly LiPo 14.8V 2100mAh 20C
Power (GPMP0618)
A cell balancer is required for the LiPo battery pack
listed above:
❏
Great Planes ElectriFly Equinox LiPo Cell Balancer
1-5 (GPMM3160)
A suitable charger is also required. The Great Planes
PolyCharge4
™ is designed for LiPo packs only. However, it
is able to charge four LiPo packs simultaneously. The Great
Planes Triton2
™ charger will only charge one pack at a time,
but is capable of charging NiCd, NiMH, LiPo, and Pb acid
batteries. Order numbers for both are provided below:
❏
Great Planes PolyCharge4 DC Only 4 Output LiPo
Charger (GPMM3015)
OR
❏
Great Planes ElectriFly Triton2 DC Comp Peak
Charger (GPMM3153)
ADDITIONAL ITEMS REQUIRED
Required Hardware and Accessories
This is the list of hardware and accessories required to
fi nish the Sequence ARF. Order numbers are provided in
parentheses:
❏
Great Planes Velcro Hook & Loop 1x6" (2)
(GPMQ4480)
❏
DuraTrax ® Servo Tape Wide 1x36" (DTXR1215)
Adhesives and Building Supplies
This is the list of Adhesives and Building Supplies that are
required to fi nish the Sequence ARF:
❏
1/2 oz. [15g] Thin Pro ™ CA (GPMR6001)
❏
Pro 30-minute epoxy (GPMR6047)
❏
Threadlocker thread locking cement (GPMR6060)
❏
Denatured alcohol (for epoxy clean up)
❏
Drill bits: 1/16" [1.6mm], 5/64" [2mm]
❏
Small metal fi le
❏
#1 Hobby knife (HCAR0105)
❏
#11 blades (5-pack, HCAR0211)
❏
Medium T-pins (100, HCAR5150)
❏
Top Flite ® MonoKote ® sealing iron (TOPR2100)
❏
Top Flite Hot Sock iron cover (TOPR2175)
❏
220 grit sandpaper
❏
Panel Line Pen (TOPQ2510)
Optional Supplies and Tools
Here is a list of optional tools that will help you build the
Sequence ARF:
❏
1/2 oz. [15g] Medium Pro CA+ (GPMR6007)
❏
1/2 oz. [15g] Thick Pro CA- (GPMR6013)
❏
2 oz. [57g] spray CA activator (GPMR6035)
❏
4 oz. [113g] aerosol CA activator (GPMR6034)
❏
CA applicator tips (HCAR3780)
❏
CA debonder (GPMR6039)
❏
Pro 6-minute epoxy (GPMR6045)
❏
Epoxy brushes 6, (GPMR8060)
❏
Mixing sticks (GPMR8055)
❏
Mixing cups (GPMR8056)
❏
Pliers with wire cutter (HCAR0625)
❏
Rotary tool such as Dremel
❏
Rotary tool reinforced cut-off wheel (GPMR8020)
❏
Servo horn drill (HCAR0698)
❏
Hobby Heat ™ micro torch II (HCAR0755)
❏
Precision Magnetic Prop Balancer (TOPQ5700)
❏
AccuThrow ™ Defl ection Gauge (GPMR2405)
❏
CG Machine™ (GPMR2400)
❏
Hobbico Flexible 18" Ruler Stainless Steel
(HCAR0460)
❏
Top Flite MonoKote trim seal iron (TOPR2200)
❏
Top Flite MonoKote heat gun (TOPR2000)
❏
Hobbico Pin Vise 1/16 Collet w/6 Bits (HCAR0696)
❏
Hobbico 8-Piece Ball Tip Hex L Wrench SAE
(HCAR0520)
❏
Great Planes Clevis Installation Tool (GPMR8030)