Great Planes Fokker Dr-1 60 ARF - GPMA1380 - Manual (Page 3)

3. You must take time to build straight, true and strong.
4. You must use an R/C radio system that is in first-class
condition, and a correctly sized engine and components
(fuel tank, wheels, etc.) throughout the building process.
5. You must correctly install all R/C and other components so
that the model operates correctly on the ground and in the air.
6. You must check the operation of the model before every
flight to insure that all equipment is operating and that the
model has remained structurally sound. Be sure to check
clevises or other connectors often and replace them if they
show any signs of wear or fatigue.
7. If you are not already an experienced R/C pilot, you
should fly the model only with the help of a competent,
experienced R/C pilot.
8. While this kit has been flight tested to exceed normal use,
if the plane will be used for extremely high stress flying, such
as dogfighting, the modeler is responsible for taking steps to
reinforce the high stress points.
Remember: Take your time and follow the instructions to
end up with a well-built model that is straight and true.
If you have not flown this type of model before, we recommend
that you get the assistance of an experienced pilot in your R/C
club for your first flights. If you're not a member of a club, your
local hobby shop has information about clubs in your area
whose membership includes experienced pilots.
In addition to joining an R/C club, we strongly recommend
you join the AMA (Academy of Model Aeronautics). AMA
membership is required to fly at AMA sanctioned clubs. There
are over 2,500 AMA chartered clubs across the country.
Among other benefits, the AMA provides insurance to its
members who fly at sanctioned sites and events. Additionally,
training programs and instructors are available at AMA club
sites to help you get started the right way. Contact the AMA
at the address or toll-free phone number below:
Academy of Model Aeronautics
5151 East Memorial Drive
Muncie, IN 47302-9252
Tele. (800) 435-9262
Fax (765) 741-0057
Or via the Internet at: http://www.modelaircraft.org
The Great Planes Fokker Dr. I ARF is an excellent sport-scale
model. Though it is not particularly large, its 60-1/4" wingspan
makes it eligible to fly in IMAA events. The IMAA (International
Miniature Aircraft Association) is an organization that promotes
non-competitive flying of giant-scale models. If you plan to
attend an IMAA event, contact the IMAA for a copy of the IMAA
Safety Code at the address or telephone number below.
IMAA
205 S. Hilldale Road
Salina, KS 67401
(913) 823-5569
If you plan to use a 2-stroke .46 or .60 size engine, you will
need to use a Pitts style muffler. The B.C.M. (Bisson Custom
Mufflers) #04061 (BISG4061) Pitts muffler or the Slimline
#3217 (SLIG2217) Pitts Style will work well for the O.S. .61
SF, FP and FX. Use the B.C.M. # 04046 (BISG4046) or the
Slimline # 3218 (SLIG2218) for the O.S. 46 SF of FX. To use
any of these mufflers, a portion of the included 60-120
engine mount may need to be trimmed.
This is the list of hardware and accessories required to finish the
Fokker Dr. I ARF. Order numbers are provided in parentheses.
❏
.46 to .60 2-stroke or .52 to .70 4-stroke
❏
4-Channel radio with five servos (two aileron servos)
❏
Propeller (refer to engine manufacturer's recommendations)
❏
3' Medium fuel tubing (GPMQ4131)
❏
Y-harness for dual aileron servos (HCAM2500 for Futaba ® J)
❏
12" Servo extension cord (HCAM2100)
❏
Two 6" Servo extension cords (HCAM2000)
❏
Switch and charge jack mounting set (GPMM1000)
In addition to common household tools and hobby tools, this
is the “short list” of the most important items required to
build the Fokker Dr. I ARF.
Great Planes Pro ™ CA and
Epoxy glue are recommended.
❏
30-Minute Epoxy (GPMR6047)
❏
1/2 oz. Thin Pro CA (GPMR6001)
❏
1/2 oz. Medium Pro CA+ (GPMR6007)
❏
Hobby knife (HCAR0105)
❏
#11 blades (HCAR0211)
❏
Single-Edge razor blades (HCAR0212)
❏
Small T-pins (HCAR5100)
❏
Builder's triangle (HCAR0480)
Adhesives and Building Supplies
Hardware and Accessories
Muffler
ADDITIONAL ITEMS REQUIRED
We, as the kit manufacturer, provide you with a top quality
kit and instructions, but ultimately the quality and flyability
of your finished model depends on how you build it;
therefore, we cannot in any way guarantee the
performance of your completed model and no
representations are expressed or implied as to the
performance or safety of your completed model.
3