GME TX4500WS - Manual (Page 17)

t X 4 5 0 0 s I n s t r u c t I o n m A n uA l PA G E 1 7
‘c9’ (or select ‘Id’ to change your radios own
selcall Ident). If an AlPhA label is displayed you
will need to press F then ALPHA to switch to
numeric mode.
3. Press and hold the channel control until the
radio beeps. the right-hand digit of the selcall
Ident will flash.
4. rotate the channel control to select the required
number in the flashing digit position.
5. Briefly press the channel control again to select
the next digit position.
6. repeat steps 4 and 5 to enter all 5 digits as
required.
7. now press and hold the channel control. the
entire Ident will flash for a few seconds then
the radio will beep as the new Ident is stored.
e.g. Programming Call Memory C5
Recalling Selcall Idents
1. Briefly press the cALL button. is displayed
along with the last sent or received selcall Ident.
2. rotate the channel control to select the required
Ident memory in locations ‘c0’ to ‘c9’.
3. Press and hold the cALL button to send the
Ident.
Naming your Selcall Idents
Your radio allows you to label each selcall Ident
using a 5 character name to make it easier to
identify callers. If an incoming selcall matches one
of those in your radio’s memory, the label can be
displayed instead of the selcall Ident.
NOTE: Before adding an AlPhA label to a selcall
Ident, you must first store the required Ident in
memory as described left.
1. Briefly press the cALL button. will be
displayed along with the last sent or received
selcall Ident.
2. rotate the channel control to select the required
Ident memory in locations ‘c0’ to ‘c9’.
3. Briefly press the F then ALPHA to select the
AlPhA mode. ALPHA will be displayed briefly.
4. If the AlPhA label is empty, ‘- - - - -’ will be
displayed, otherwise it will display the last AlPhA
label programmed into that memory.
5. Press and hold the channel control until the
radio beeps. the left-hand position of the Alpha
label will flash.
6. rotate the channel control to select the
required character in the flashing position then
briefly press the channel control again to select
the next position.
7. repeat step 6 to enter up to 5 characters
as required.
8. now press and hold the channel control. the
entire Alpha label will flash for a few seconds
then the radio will beep as the label is stored.
e.g. Labelling Call Memory C5
repeat steps 2 to 8 to add AlPhA labels to any
other selcall Idents stored in memory. the following
characters are available;
Letters A B c D E F G h I J K l m n o
P Q r s t u V w X Y Z
Numbers 0 1 2 3 4 5 6 7 8 9
Punctuation * +
To exit the cALL TO mode, briefly press the cALL
button (or simply wait for the call function to time
out). the radio will return to normal operation.
To display the Alpha labels of incoming
Selcalls, the radio should be left in Alpha mode.
Any incoming selcall that does not match those in
the memory will display -nEw-. to display the selcall
Ident of that caller, briefly press F then ALPHA to
return to the numErIc mode.
Receiving Selcalls
when your radio receives it’s selcall Ident, an alarm
will sound to alert you to the call. Initially the alarm
will beep urgently at 2 beeps per second, then, if
the call is not answered, it will slow to around 1
beep every 3 seconds. It will then continue to beep
indefinitely until you cancel it.
46885-4_TX4500S_IM.indd 17 4/06/14 3:08 PM