Futaba 12FG - Manual (Page 62)

62
S1 button
EDIT button
EDIT dial
ŏ3XVKWKHS1EXWWRQIRU
VHFRQGWRUHWXUQWRWKH
KRPHVFUHHQ
ŏ7XUQ WKH EDIT GLDO WR
PRYHRQWKHVFUHHQ
ŏ6 H O H F W W K H I X Q F W L R Q
QDPH DQG UHWXUQ WR WKH
S U H F H G L Q J V F U H H Q E \
SXVKLQJWKHEDITEXWWRQ
THROTTLE CUT 6WRSVWKHHQJLQHVDIHO\DQGHDVLO\DLUSODQHDQGKHOLFRSWHURQO\
Throttle cut provides an easy way to stop the
HQJLQHE\ÀLSSLQJDVZLWFKZLWKWKHWKURWWOHVWLFN
at idle. The action is not functional at high throttle
to avoid accidental dead sticks. The switch’s
location and direction must be chosen, as it defaults
to NULL.
Throttle cut setting procedure
*Perform the following settings before using the EDIT dial to
move the cursor to the item to be set.
$FWLYDWHWKHIXQFWLRQ
0RYH WKH FXUVRU WR WKH >$&7,1+@ LWHP DQG
SXVK WKH (',7 EXWWRQ WR VZLWFK WR WKH GDWD
LQSXWPRGH
7XUQWKH(',7GLDOWRWKHOHIWXQWLOWKHEOLQNLQJ
FKDQJHV IURP ,1+ WR $&7 DQG WKHQ SXVK
WKH(',7EXWWRQ
6ZLWFKVHWWLQJ
0RYH WKH FXUVRU WR WKH >6:,7&+@ LWHP DQG
FDOOWKHVZLWFKVHWXSVFUHHQE\SUHVVLQJWKH
(',7 EXWWRQ DQG VHOHFW WKH VZLWFK DQG 21
GLUHFWLRQ
(For a detailed description of the setting method, see [Switch
Setting Method] at the back of this manual.)
7KURWWOHFXWSRVLWLRQVHWWLQJ
0RYHWKHFXUVRUWRWKH>&87326,7,21@LWHP
DQG SXVK WKH (',7 EXWWRQ WR VZLWFK WR WKH
GDWDLQSXWPRGH
$GMXVWWKHVHUYRRSHUDWLRQSRVLWLRQDWWKURWWOH
FXWRSHUDWLRQE\WXUQLQJWKH(',7GLDOWRWKH
OHIWRUULJKW
,QLWLDOYDOXH
$GMXVWPHQWUDQJHa
(When the EDIT button is pressed for 1 second, the servo
operation position is reset to the initial value.)
3XVKWKH(',7EXWWRQWRHQGDGMXVWPHQWDQG
UHWXUQWRWKHFXUVROPRYHPRGH
*With the selected cut switch ON and the throttle stick at idle;
adjust the rate until the engine consistently cuts off.
However, be sure that the throttle linkage is not pulled too
tight and unreasonable force is not applied to the servo.
ŏ 6HOHFW >7+5277/( &87@ DW WKH OLQNDJH PHQX DQG
FDOOWKHVHWXSVFUHHQVKRZQEHORZE\SXVKLQJWKH
(',7EXWWRQ
ŏ&XUUHQWWKURWWOHSRVLWLRQ ŏ&XWSRVLWLRQ