Comtrol RM II V.90 User Manual
Hardware installation card, Rocketmodemii™ v.90
Table of contents
Document Outline
- Product Overview
- Utilizing V.90 Technology
- Installing the RocketModemII
- 1. Turn your computer off and remove the system unit cover.
- 2. Select an available PCI slot and remove the slot cover.
- 3. Write down the serial number of the RocketModemII.
- 4. Insert the RocketModemII in the expansion slot. Make sure it is seated securely.
- 5. Reinstall the expansion slot cover screw.
- 6. Connect standard RJ11 (telephone) cables between the RocketModemII ports and the phone line ja...
- 7. Power up the computer and run the Diagnostics program to verify that the RocketModemII is inst...
- 8. After the RocketModemII has successfully passed diagnostics, install and configure the device ...
- Port Identification
- Using the Diagnostics
- 1. Insert the Diagnostics diskette in the floppy drive.
- 2. Power up the machine. The diagnostic program starts automatically on boot-up.
- 3. Press any key to continue.
- 4. Press any key to continue.
- 5. Select the letter that corresponds to the model you installed, select NOT INSTALLED if you hav...
- a. Select the letter for the I/O address you used when installing the card. A list of valid IRQ i...
- b. Select the letter for the IRQ you used when installing the card.
- c. The diagnostic program loops back to Step 5.
- d. If you have more than one ISA RocketModem installed, repeat this step until you have entered t...
- 6. If the list is correct, press Y. If the information is not correct, press N to restart the dia...
- 7. After initialization completes, an option box displays at the bottom of the screen:
- 8. Press D to test the serial I/O and IRQ. (The T and M options are discussed under Terminal Mode...
- 9. Press any key to continue. If you have more than one card installed, the diagnostic repeats un...
- 10. Press any key to continue. The diagnostic displays a summary of the test results.
- 11. Press any key to continue.
- 12. Press Y to restart the diagnostic at Step 3 (for example, to enter Terminal Mode), or N to quit.
- 1. If there is more than one RocketModem installed, you are asked to select a card. Do so.
- 2. A numbered menu listing the ports on the selected card displays. You may also press H for help...
- 3. Enter a port number to select a modem. The Terminal Mode screen displays.
- 4. Type AT commands to communicate with the modem.
- 5. When you are done, press Esc to return to Step 2.
- 1. Select Port 1.
- 2. Enter AT&F0 to initialize the modem to factory default parameters.
- 3. Enter ATS0=1 to direct the modem to answer the phone on the first ring.
- 4. Press Esc to return to the port menu.
- 5. Select Port 2.
- 6. Enter AT&F0 to initialize the second modem.
- 7. Enter ATDxxx xxxx (where xxx xxxx is the phone number of the line connected to the first modem).
- 8. Press Esc.
- 9. Select Port 1. You should see RING and CONNECT messages.
- 10. Any keys you press while looking at Port 1 display when you look at Port 2. Likewise, any key...
- 11. To exit, on either of the ports enter the escape sequence +++. This enables you to enter ATH ...
- 12. To exit terminal mode and return to the port menu, press Esc.
- Using the Speaker
- Modem Cables
- FCC Notices
- 1. This equipment complies with Part 68 of FCC rules. On the bottom panel of the unit is a label ...
- 2. The RocketModemII uses FCC compliant modular plugs, it is designed to be connected to the tele...
- 3. If this equipment causes harm to the telephone network, the telephone company will notify you ...
- 4. The telephone company may make changes in its facilities, equipment, operations, or procedures...
- 5. If the equipment is causing harm to the network, the telephone company may request you to remo...
- 6. No repairs are to be made by you. Repairs are to be made only by Comtrol or its licensees. Una...
- 7. This equipment may not be used for public coin phone service provided by the Telephone Company...
- 8. The Telephone Consumer Protection Act of 1991 makes it unlawful for any person to use a comput...
- Operating Conditions
- Hardware Specifications
- Electromagnetic Compliance
- Technical Support
- RocketModemII™ V.90
- Hardware Installation Card