Cleaning and maintenance – Kenmore 141.16223 User Manual
Page 19
Attention! The text in this document has been recognized automatically. To view the original document, you can use the "Original mode".
Cleaning and Maintenance
As with all appliances, proper care and maintenance
will keep your grill in top operating condition and
prolong its life. By following these cleaning procedures
on a timely basis, your grill will stay clean and work
properly with minimum effort.
Important Note: Use a sponge or washcloth to clean
exterior grill surfaces. A fiber or brass cleaning brush
can be used to clean interior grill parts which will
accumulate food and grease; Grill Bowl, Cooking
Grids, Flame Tamers, Grease Draining Tray and
Grease Receptacle. Never use a wire brush or metal
scraper which can scratch or chip the porcelain finish
of your grill and promote rusting which is not covered
by your product warranty.
Cleaning the Cooking Grids
Before initial use and as needed, wash Cooking Grids
with a mild detergent and rinse with hot water. For
stubborn food residue use a degreaser and fiber or
brass cleaning brush. Dry immediately using a soft
cloth or paper towels.
CAUTION: Never clean your grill unless you are
sure it is cool to the touch.
Cleaning the Flame Tamers
To reduce the chance of flare-ups. Flame Tamers
should be cleaned whenever food or grease drippings
accumulate. Wash Flame Tamers with a mild deter
gent and rinse with hot water. Dry the Flame Tamers
thoroughly before you reinstall them into the grill bowl.
To remove stubborn food residue use a degreaser and
fiber or brass cleaning brush.
Cleaning the Grease Draining Tray, Heat Shield
and Grease Receptacle
To reduce the chance of fire, the Grease Draining Tray,
Heat Shield and Grease Receptacle should be in
spected before each grill use. Remove grease
(a plastic spatula works well) and wash all parts with a
mild soap and warm water solution.
Cleaning Exterior Surfaces
Before initial use, and periodically thereafter, we
suggest you wash your grill using a mild soap and
warm water solution. You can use a wash cloth or
sponge for this process. Do not use a stiff wire or
brass brush that might remove paint during the clean
ing process.
Keep outdoor cooking gas appliance area clear and
free from combustible materials, gasoline and other
flammable vapors and liquids.
Cleaning the Inside of the Grill Lid
Grease can have a tendency to build up on the inside
of the Grill Lid and could drip onto deck or patio when
the lid is opened. Visually inspect the inside of the
Grill Lid before each grill use. Remove any grease and
wash with a mild soap and warm water solution.
Cleaning the Grill Interior
Burning-off the grill after every cookout will keep it
ready for instant use. However, once a year you should
give the entire grill a thorough cleaning to keep it in top
operating condition. Follow these steps:
1. Turn all Burner Valves to the full OFF position.
2. Turn the LP gas tank valve to the full OFF position.
3. Disconnect the regulator from the gas tank. Inspect
the hose with regulator assembly for cracking, cuts
or any other damage, and replace as neccessary
with Sears replacement parts. See Parts List.
4. Remove and clean the Flame Tamers, Cooking
Grids, Cooking Rack and Grill Burners.
5. Cover each Gas Valve Orifice with aluminum foil.
6. Brush the inside and bottom of the grill with a fiber
or brass cleaning brush, and wash with a mild
soap and warm water solution. Rinse thoroughly
and let dry.
7. Remove aluminum foil from Orifices and check
each Orifice for obstruction.
8. Check each Spark Electrode, adjusting as needed.
The space between the Spark Electrode Tip and
Spark Receiver should be approximately 3^ 6".
9. Replace tiie Burners and adjust the Gas Collector
Box. The edge of the collector box should be
overlapping the Burner Port.
10. Replace Flame Tamers and the Cooking Grids.
11. Reconnect the gas source and observe the Burner
flame for correct operation.
CAUTION:
1. Do not obstruct the flow of air for combustion
and ventilation.
2. Keep the ventilation openings of the cylinder
enclosure cabinet free and clear of debris.
3. Visually check burner flames occasionally to
observe for proper flame pattern as shown below.
BURNER FLAME
19