Generai care & cleaning (cont’d), If n e cessa ry – Kenmore 790.7011 User Manual
Page 11
Attention! The text in this document has been recognized automatically. To view the original document, you can use the "Original mode".
Generai Care & Cleaning (cont’d)
Cleaning Chart
Surfaces
How to Clean
Glass,
Painted
Plastic Body Parts
&
Control Knobs
Fo r g e n e ra l cle a n in g ,
use a soft cloth, clean with mild dish detergent & water or a 50/50 solution
of vinegar & water. Follow by rinsing the area with clean water; dry & polish with a soft cloth.
Glass cleaners may be used if sprayed on a soft cloth 1st.
DO NOT
spray liquids directly on the
control pad and display areas.
DO NOT
use large amounts of water on the control panel - excess
water on the control area may cause damage to the appliance.
DO
NOT
use other liquid
cleaners, abrasive cleaners, scouring pads, or some paper towels - they will damage the finish.
Painted Control
Panels & Display
areas
B e fo re clea n in g th e co n tro l p a n e l,
turn all controls to OFF & remove the control knobs. To
remove, pull each knob straight off the shaft. Use the
g e n e ra l cle a n in g
instructions provided in the
paragraph above.
Porcelain Enamel
Burner Grates,
Cooktop Surface,
Broiler Pan & Insert,
Broiler Drawer, Door
Liner
&
Oven Bottom
Clean burner grates, broiler pan & insert in the dishwasher and dry upon removal. If soils are not
removed, follow the cooktop cleaning instructions below.
Gentle scouring with a soapy scouring pad will remove most spots. Rinse with a 1:1 solution of
clean water & ammonia.
If n e cessa ry,
cover difficult spots with an ammonia-soaked paper towel
for 30 to 40 minutes. Rinse with clean water and a damp cloth, then scrub with a soap-filled
scouring pad. Rinse & wipe dry with a clean cloth. Remove all cleaners or the porcelain may
become damaged during future heating.
DO NOT
use spray oven cleaners on the range top.
Oven Racks
Remove racks. See "Removing & Replacing Oven Racks" under Before
Setting Oven Controls.
Use a mild, abrasive cleaner, following the cleaner’s recommendations. Rinse with clean water &
let dry. After cleaning the racks, rub the sides of the racks with wax paper or a cloth containing a
small amount of salad oil (this will make the racks glide easier into the oven rack positions).
Oven Door
Use soap & water to thoroughly clean the top, sides & front of the oven door. Rinse well. You
may use a glass cleaner on the outside glass of the oven door.
DO NOT
immerse the door in
water.
DO NOT spray
or
allow water or the glass
cleaner
to enter
the
door vents.
DO NOT
use oven cleaners, cleaning powders or any harsh abrasive cleaning materials on the outside of
the oven door.
DO NOT
clean the oven door gasket. The oven door gasket is made of a woven
material, on Self-Cleaning models, which is essential for a good seal. Care should be taken not
to rub, damage or remove this gasket.
Stainless
Steel
Clean
stainless
steel with hot soapy water & a dishcloth. Rinse with clean water and a cloth.
DO NOT use cleaners with high conecentrations of chlorides or chlorines. DO NOT use harsh
scrubbing cleaners. Only use kitchen cleaners that are especially made for cleaning stainless
steel. Always be sure to rinse the cleaners form the surface as bluish stains may occur during
heating that cannot be removed.
Countoured well
areas, bruner caps
&
burner heads
See
Cleaning the Countoured Well
Areas,
Burner Caps
&
Burner Heads
section for
complete details.
Cleaning the
Cooktop
The cooktop is designed to make cleaning easier. Because the four burners are sealed, cleanups are easy when spillovers
are cleaned up Immediately. To clean, wipe with a clean, damp cloth and wipe dry.
Cleaning the Contoured Well Areas, Burner Caps & Burner Heads
The contoured well areas, burner caps and burner heads should be routinely cleaned. Keeping the burner ports clean will
prevent improper ignition and an uneven flame. Refer to the following section for instructions.
THE COOKTOP IS NOT REMOVABLE.
Do not attempt to remove or lift
the
cooktop.
^CAUTION
Use caution when replacing the burner cap
so the electrode is not damaged. This may cause a
delayed ignition or prevent the burnerfrom igniting.
^CAUTION
|Anyadditions,changesorconversions
required
in order for this appliance to perform satisfactorily must be
made by an authorized Sears Service Center.
11