Start, Options – GE EDWSO00 User Manual

Page 5

Attention! The text in this document has been recognized automatically. To view the original document, you can use the "Original mode".

ge.com

SPEED CYCLE
or
SPEED WASH

(on some models)

7.3 gal., 35 min.

This cycle is for everyday dishes and glassware.

CHINA CRYSTAL

(on some models)

7.3 gal., 48 min.

This cycle is for lightly soiled china and crystal.

RINSE ONLY

2.5 gal., 12

min.

For rinsing partial loads that will be washed later. Do not use detergent with this cycle.

NOTE:

Only the Anti-Bacteria cycle has been designed to meet the requirements of Section 6, NSF18A for

soil removal and sanitization efficacy.

Options

The light above the selected pad will be ON

indicate which option has been selected.

PRESCRUB

(on some models)

For use with heavily soiled and/or dried-on, baked-on soils. This option

MUST

be selected

PRIOR

starting the cycle.

This option adds 16

minutes

to the cycle time. NOTE:

Cannot be selected with

RINSE ONLY

cycle.

HEATED DRY

Light OFF

Shuts off the drying heat option. Dishes air dry naturally and energy is saved. For faster air dry,
you can prop the door open after the

CLEAN

light Illuminates.

HEATED DRY

Light ON

Turns the heater on for fast drying. This will extend the total run time by 8 minutes for the

SPEED

CYCLE,

38 minutes for

NORMAL

and

POTS/PANS,

and 30 minutes for all other cycles.

NOTE:

Cannot be selected with

RINSE ONLY

cycle.

LOCK

You can lock the controls to prevent any selections from being made. Or you can lock the controls
after you have started a cycle.

Children cannot accidentally start dishwasher by touching pads with this option selected.

To LOCK the dishwasher control,

touch and hold the

HEATED DRY

pad for 3 seconds. The light

below the

HEATED DRY

pad will turn on.

To UNLOCK the dishwasher control,

touch and hold the

HEATED DRY

pad for 3 seconds. The

LOCK

light will turn off.

ADDED

HEAT

When selected, the cycle will run longer with the heating element on to Improve both wash and

dry performance.

NOTE:

Cannot be selected with

RINSE ONLY

cycle.

DELAY HOURS

You can delay the start of a wash cycle for up to 9 hours. Touch the

DELAY HOURS

pad to choose

the number of hours you want to delay the start of the cycle; then touch

START/RESET

one time.

The dishwasher will count down and start automatically at the correct time.

Touching

START/RESET

a second time will cancel the

DELAY START

selection.

(Л

r~t-

1Л

о-

гь"

(Л

3“

Е+

з'

■о

(Л

RESET

То change а cycle after washing starts, touch the

START/RESET

pad to cancel the cycle. The

START/RESET

light will flash while the water is pumped out if needed. This takes approximately

90 seconds. When the light stops flashing, the dishwasher can be reprogrammed and restarted.

Start

Close and latch the dishwasher door and select the cycle and desired enhancements. Touch the

START/RESET

pad

once to begin the cycle. Water begins to fill the dishwasher, and approximately 60 seconds later the wash action
begins. Touching the

START/RESET

pad a second time will cancel the cycle and cause the water to drain out. This will

take approximately 2 minutes.

NOTE:

The dishwasher remembers your last cycle so you don't have to reprogram each time. When the dishwasher

door is fully closed, the control panel lights will display the last settings you selected.

If you don't want to change any of the settings, simply touch the

START/RESET

pad once to begin the cycle.

If the door is closed, the indicator lights will turn off if the

START/RESET

pad is not pressed within two minutes.

To activate the display, open and close the door or touch any pad.

Also, if a power failure occurs,

NORMAL

and

HEATED

DRt'

will automatically be programmed.

(л

<ъ

Uì

тз
■D