AXEON AT-Series - Manual (Page 26)

AT – Series User’s Manual
MKTF-205
WARNING: THE BRINE SEAL MUST BE IN THE SAME POSITION FOR
EACH MEMBRANE ELEMENT HOUSING, SO MARK EACH HOUSING PRIOR TO
REMOVING THE MEMBRANE
THAT PROTRUDES ON ONE SIDE OF THE MEMBRANE AND
FEED SIDE OF THE MEMBRANE
1. Remove one membrane
housings, from the top of the housing. L
the old membrane element out of the membrane element housing.
2. Lubricate the brine seal
3. Install the brine seal side
When the housings have a direction of flow from bottom to top, the brine seal
should be located at the bottom of the housing.
4. At a slight angle, insert
careful not to tear or flip the brine seal.
insert the membrane element, to ensure
the brine seal if necessary.
5. With a smooth and constant motion, push the membrane e
housing so the brine seal enters the ho
groove.
6. Re-install the end caps by gently twisting the end cap while pushing it onto the
housing. Ensure that you do not pinc
the end plug. Push the end plug on until
with the outer diameter of the membrane housing.
7. Insert the snap ring until
8. Reconnect any fittings that may have been disconnected when the membrane
element housings were disassembled.
9. To start-up the system,
(See Page 20)
CAUTION: WET MEMBRANES ARE SHIPPED IN A PRESERVATIVE
SOLUTION. THE MEMBRANES MUST BE FLUSHED FOR AT LEAST 1 HOUR TO
REMOVE THE PRESERVATIVE FROM THE MEMBRANE. DISCARD ALL OF THE
PERMEATE AND CONCENTRATE, WHICH IS PRODUCED DURING THE FLUSH
PERIOD.
26
WARNING: THE BRINE SEAL MUST BE IN THE SAME POSITION FOR
ELEMENT HOUSING, SO MARK EACH HOUSING PRIOR TO
THE MEMBRANE ELEMENTS. THE BRINE SEAL IS A RUBBER SEAL
ON ONE SIDE OF THE MEMBRANE AND IS ALWAYS ON THE
MEMBRANE ELEMENT.
Remove one membrane element at a time from the membrane element
from the top of the housing. Long nose pliers may be necessary to pull
the old membrane element out of the membrane element housing.
seal with non petroleum based lubricant, Silicone DC 111
Install the brine seal side of the membrane element first (Figure 4, Page 27
hen the housings have a direction of flow from bottom to top, the brine seal
should be located at the bottom of the housing.
insert the membrane while slightly rotating the
careful not to tear or flip the brine seal. A slow twisting motion should be used to
e element, to ensure the brine seal stays in place.
the brine seal if necessary.
With a smooth and constant motion, push the membrane element into the
the brine seal enters the housing without coming out of the brine seal
install the end caps by gently twisting the end cap while pushing it onto the
housing. Ensure that you do not pinch or fatigue any O-rings while re
. Push the end plug on until the outer diameter of the plug is flush
with the outer diameter of the membrane housing.
snap ring until it is fully seated. Install the locking clip if available.
econnect any fittings that may have been disconnected when the membrane
nt housings were disassembled.
p the system, please refer to the Initial Start-Up section of this manual
MEMBRANES ARE SHIPPED IN A PRESERVATIVE
SOLUTION. THE MEMBRANES MUST BE FLUSHED FOR AT LEAST 1 HOUR TO
REMOVE THE PRESERVATIVE FROM THE MEMBRANE. DISCARD ALL OF THE
PERMEATE AND CONCENTRATE, WHICH IS PRODUCED DURING THE FLUSH
06/12
WARNING: THE BRINE SEAL MUST BE IN THE SAME POSITION FOR
ELEMENT HOUSING, SO MARK EACH HOUSING PRIOR TO
ELEMENTS. THE BRINE SEAL IS A RUBBER SEAL
S ALWAYS ON THE
from the membrane element
pliers may be necessary to pull
the old membrane element out of the membrane element housing.
ant, Silicone DC 111.
Figure 4, Page 27).
hen the housings have a direction of flow from bottom to top, the brine seal
the element being
slow twisting motion should be used to
the brine seal stays in place. Re-lube
lement into the
using without coming out of the brine seal
install the end caps by gently twisting the end cap while pushing it onto the
rings while re-installing
the outer diameter of the plug is flush
locking clip if available.
econnect any fittings that may have been disconnected when the membrane
section of this manual.
MEMBRANES ARE SHIPPED IN A PRESERVATIVE
SOLUTION. THE MEMBRANES MUST BE FLUSHED FOR AT LEAST 1 HOUR TO
REMOVE THE PRESERVATIVE FROM THE MEMBRANE. DISCARD ALL OF THE
PERMEATE AND CONCENTRATE, WHICH IS PRODUCED DURING THE FLUSH