Hangar 9 33% Pawnee 80cc ARF (3 Boxes) - Manual (Page 4)

4 Hangar 9 33% Pawnee 80cc ARF
Safe Operating Recommendations
• Inspect your model before every flight to make certain it
is airworthy.
• Be aware of any other radio frequency user who may
present an interference problem.
• Always be courteous and respectful of other users of
your selected flight area.
• Choose an area clear of obstacles and large enough to
safely accommodate your flying activity.
• Make certain this area is clear of friends and spectators
prior to launching your aircraft.
• Be aware of other activities in the vicinity of your flight
path that could cause potential conflict.
• Carefully plan your flight path prior to launch.
• Abide by any and all established AMA National Model
Aircraft Safety Codes.
Important Information
Regarding Warranty
Please read our Warranty and Liability Limitations section on
page 59 before building this product. If you as the purchaser
or user are not prepared to accept the liability associated
with the use of this Product, you are advised to return this
Product immediately in new and unused condition to the
place of purchase.
Using the Manual
This manual is divided into sections to help make assembly
easier to understand, and to provide breaks between each
major section. In addition, check boxes have been placed
next to each step to keep track of the steps completed. Steps
with a single box (  ) are performed once, while steps with
two boxes (  ) indicate the step will require repeating,
such as for a right or left wing panel, two servos, etc.
Remember to take your time and follow the directions.
UltraCote® Covering Colors
White HANU870
True Red HANU866
Sky Blue HANU875
Recommended Engine
Zenoah ® GT80 Twin Cylinder ZENE80T
24” Diameter Gas-Series Prop, A-Pitch VSS2401
Spinner TRUTT-3752-B-M-DA100
Transmitter Requirements
This model requires a minimum of a 5-channel radio to
operate all the functions of your aircraft. We suggest the
following radio systems available through Horizon Hobby or
your local hobby distributor.
JR 9503 JRP2930X
JR 11X JRP1100X
Spektrum ™ DX8 SPM8800
Spektrum DX10t SPM2800US
JR ® DSM2 ™ or DSMX ™ Systems
Radio Equipment Requirements
The following items are recommended when installing the
9-Channel AR9100 receiver (SPMAR9100) in your aircraft:
AR9000 DSM2 9-Channel Receiver SPMAR9010
3-inch (152mm) Servo Extension (2) JRPA093
12-inch (305mm) Servo Extension (4) JRPA098
18-inch (457mm) Servo Extension (3) JRPA099
24-inch (610mm) Servo Extension JRPA102
36-inch (915mm) Servo Extension (3) JRPA103
6.0V Receiver Battery, 2700mAh JRPB5008
Aluminum Servo Arm, 3-inch (152mm) JRPA237
Aluminum Servo Arm, 1 1 /
2
-inch (38mm) (7) HAN9154
A6020 Digital Aircraft Servo, High-Torque (8) SPMSA6020
Required Tools
Crimping tool Drill
Epoxy brush Felt-tipped pen
Flat blade screwdriver Fuel tubing
Hobby knife with #11 blade Isopropyl alcohol
Light machine oil
Linkage wrench (optional)
Low-tack tape Medium grit sandpaper
Mixing cup Mixing stick
Nut driver: 1/4-inch Paper towel
Pencil Petroleum jelly
Phillips screwdriver: #1 Pin vise
Pliers Scissors
Side cutter Ruler
String or dental floss Toothpicks
Drill bit: 1/16-inch (1.5mm), 5/64-inch (2mm),
5/16-inch (8mm)
Hex wrench: 1.5mm, 5/64-inch, 3/32-inch,
1/8-inch, 3/16-inch
Open-end wrench: 3/16-inch, 7mm, 1/4-inch, 11/32-inch
Required Adhesives
Formula 560 Canopy Glue (PAAPT56)
30-Minute Epoxy, 8 oz (PAAPT39)
Thin CA (PAAPT08)
Threadlock (PAAPT42)
Field Equipment Required
Ultra Fuel Pump Glow/Gas HAN155
G62/38/45/445 Spark Plug ZEN6242
Evolution ® 2-cycle oil EVOX1001Q
Pilot Figure HAN8265