Wilbur Curtis D500GT - Manual (Page 3)

3
Program Menus
From Program Menus press > display will now show the next feature.
Selecting Brew by Volume or Brew by Time depends on whether you know your brew time before starting.
Brew by Volume (Factory set to 74oz)
Press  to Select, display will now show Press BREW to Start. Press the BREW button. The unit will start spraying hot water
into the brewcone. When correct volume is reached press BREW button again to stop the flow. Now the volume has been set.
Pressing > button will display the subsequent menu features.
Brew by Time (Factory set to 3 min)
Press  to Select, display will now show Select Button. The current time is now shown. By pressing < > you can toggle back
and forth from minutes to seconds to exit (ex). Change the time or set and exit by pressing .
Temperature (Factory set to 200°F)
Press  to Select. Press < > to move to desired temperature and then  to set. Temperature is programmable from 170ºF to
206ºF in 2-degree increments.
Energy Save Mode (Factory set to OFF)
Press  to Select, < , >, ON, OFF or ON 140ºF ,  to set. When in ON, unit will automatically shut off 4 hours from last
brew. When feature is OFF, unit does not have the energy saving mode.
In the ON 140ºF position, temperature goes down to 140ºF. if unit has not brewed in 4 hours. This feature will save energy by
lowering the tank temperature during periods of non-operation.
Brew Count Odom.
Press  to display total gallons brewed. Press ex or Reset.
Pre-Infusion (Factory set to OFF)
Press  to Select. Display will now show Select Button. Select desired Brew button. Current setting in seconds is displayed <
to decrease or select > to increase (range from OFF to 10 through 60 seconds),  to set.
If Pre-infusion is selected (ON), Cold Brew Lock is set within 5ºF of set point and Cold Brew Lock and Pulse Brew
dissappears from the list of program selections.
Quality Timer (Factory set to OFF)
Press  to select. Press > to select OFF, ON, then increase time from 20 minutes to a maximum of 120 minutes. Increments
are 10 minutes. Press  to set. Timing starts at the begining of a brew cycle. An audible alarm will sound when time has
expired. Press the ON/OFF button on the control pannel to shut it off.
Brew Count Total
Press  to Select, Shows total gallons and total brew cycles on the unit. Brew Count Total cannot be reset.
Cold Brew Lock . . . (Factory set to 15º)
Press  to select, < > to select desired setting (CBL 5, 15 or OFF), to set.
The Cold Brew Lock feature allows the brewer to brew at three different temperature levels below the actual set point. The first
setting is within 5 degrees of set point, next is within 15 degrees of set point, OFF is within 30 degrees of set point for the Ready
to Brew message, however it will brew at any temperature.
Master Reset
Press  to display Are You Sure? Then < for Yes, or > for No.
Brewer factory defaults are then reset.
Service Call (Phone number Factory set to 1-800-000-0000X)
Press  to display number and change number or < to move place and EX to exit when complete This number will be dis-
played during a Heating system SENSOR ERROR or during a WATER ERROR.
Temperature
Brew By Time
Brew By Volume
Program Menus
Energy Save Mode
Brew Count Odom
Continued, Page 4
Program Menus
Model Select - D500GT ONLY. Always perform this first. This feature re-sets all settings to the factory defaults.
Scroll through menu to Model Select. Choices are: ALPHA-1, ALPHA-2, ALPHA-3/4/5, Airpot Brewer and Thermo-Alpha. Select only Airpot
Brewer.
Master Reset
Pre-Infusion
Brew Count Total
Cold Brew Lock
Service Call
Quality Timer