Nexen 5H70P 917500 User Manual
Page 17
17
FORM NO. L-20008-V-0511
16. Install the new O-Ring Seal (Item 13) into the Cylinder
(Item 2) and the new O-Ring Seal (Item 12) onto the
Piston (Item 3).
17. Making sure not to damage the new O-rings Seals
(Items 12 and 13), press the Piston (Item 3) into the
Cylinder (Item 2).
18. Press the Drive Ring (Item 4) into the new Ball Bearing
(Item 8) and Cylinder (Item 2).
19. Loosen the Set Screws (Item 16) and remove the
Locking Collar (Item 19).
20. Remove the Retaining Ring (Item 11).
21. Remove the Spacer (Item 18).
22. Press the Hub (Item 1) out of the Drive Flange (Item
15).
NOTE: Do not remove the Backing Plate (Item 6) from the
Hub (Item 1).
23. Remove the Retaining Ring (Item 10) from the Drive
Flange (Item 15).
24. Press the two old Ball Bearings (Item 9) out of the
Drive Flange (Item 15).
25. Clean the bearing bore of the Drive Flange (Item 15)
with fresh safety solvent, making sure all old Loctite®
residue is removed.
26. Apply an adequate amount of Loctite® 680 to evenly
coat the outer race of the two new Ball Bearings (Item
9); then, press the two new Ball Bearings (Item 9) into
the Drive Flange (Item 15).
27. Reinstall the Retaining Ring (Item 10).
28. Press the Hub (Item 1) into the Drive Flange (Item 15)
and new Ball Bearings (Item 9).
29. Install the Spacer (Item 18).
30. Reinstall the Retaining Ring (Item 11).
PARTS REPLACEMENT (5H100P continued)
Apply a
thin coat of
Never-Seez®.
FIGURE 18
1
15
4
18
2
11
7
19
16
CAUTION
Working with spring loaded or tension
loaded fasteners and devices can cause
injury. Wear safety glasses and take the
appropriate safety precautions.
31. Install the Locking Collar (Item 19) and secure it to the
Hub (Item 1) with the Set Screws (Item 16).
32. Install the new Compression Springs (Item 7).
33. Apply a thin coat of Never-Seez® to the teeth of the
Drive Ring (Item 4).
34. Press the Drive Flange (Item 15) and Hub (Item 1) into
the Cylinder (Item 2) and Drive Ring (Item 4).
35. Install the Spacer (Item 18).
36. Reinstall the Retaining Ring (Item 11).
37. Install the Locking Collar (Item 19) and secure it to the
Hub (Item 1) with the Set Screws (Item 16)
- 5H60P 917400 5H50P 917300 5H45P 917200 5H40P 917100 5H35P 917000 5H30P 916900 5H100P 916710 5H60P 910403 5H80P 916100 5H70 916800 5H60 916700 5H50 916600 5H45 916500 5H40 916400 5H35 916300 5H30 916200 5H50S 910328 5H80P 911703 5H70P 910504 5H50P 910303 5H45P 910203 5H40P 910103 5H35P 910003 5H30P 909903 5H80P 911702 5H80P 911719 5H70P 910525 5H80P 911704 5H70P 910503 5H60P 910433 5H50P 910305