Clarion DXZ378RMP - Manual (Page 12)

Basic Operations
English
12
DXZ378RMP/DXZ379RMP
Sound Adjustment
You can adjust a sound effect or tone quality to
your preference.
● Setting the Z-Enhancer
This unit are provided with 3 types of sound
tone effects stored in memory.
Select the one you prefer.
∗ The factory default setting is “ OFF ”.
2-1. Select “ Z-EHCR ”.
3-1. Each time you press the [ w ] or [ z ]
button, the tone effect changes in the
following order:
“ EXCITE ” ↔ “ IMPACT ” ↔ “ B-BOOST ” ↔
“ OFF ”
EXCITE : bass and treble emphasized
mid deemphasized
IMPACT : bass and treble emphasized
B-BOOST : bass emphasized
OFF : no sound effect
When “EXCITE” is set:
3-2. Press the [ ] button.
3-3. Press the [ w ] or [ z ] button to adjust the
bass and treble in the range of +3 to –3.
∗
The factory default setting is “ 0 ”.
3-4. Press the [ ] button to return to previous
mode.
When “IMPACT” is set:
3-2. Press the [ ] button.
3-3. Press the [ w ] or [ z ] button to adjust the
bass and treble in the range of +3 to –3.
∗
The factory default setting is “ 0 ”.
3-4. Press the [ ] button to return to previous
mode.
When “B-BOOST” is set:
3-2. Press the [ ] button.
3-3. Press the [ w ] or [ z ] button to adjust the
bass in the range of +3 to –3.
∗
The factory default setting is “ 0 ”.
3-4. Press the [ ] button to return to previous
mode.
● Adjusting the bass
This adjustment can be performed only when
the Z-Enhancer is set to “
OFF ”.
2-1. Select “ BASS ”.
3-1. Press the [ w ] or [ z ] button to adjust the
bass.
∗
The factory default setting is “ 0 ”.
(Adjustment range: +8 to –8)
● Adjusting the treble
This adjustment can be performed only when
the Z-Enhancer is set to “
OFF ”.
2-1. Select “ TREBLE ”.
3-1. Press the [w] or [z] button to adjust the
treble.
∗
The factory default setting is “ 0 ”.
(Adjustment range: +7 to –7)
● Adjusting the balance
2-1. Select “ BALANCE ”.
3-1. Press the [w] or [z] button to adjust the
balance of the right and left speakers.
∗
The factory default setting is “ CENTER ”
(center). (Adjustment range: RIGHT12 to
LEFT12 (right 12 to left 12))
● Adjusting the fader
2-1. Select “ FADER ”.
3-1. Press the [w] or [z] button to adjust the
balance of the rear and front speakers.
∗
The factory default setting is “ CENTER ”
(center). (Adjustment range: FRONT12 to
REAR12 (front 12 to rear 12))
Note:
• During SOUND adjustment mode, if no operation
is performed for more than 10 seconds, this
mode can be cancelled and return to previous
mode.
To change sound setting
1. Press the [ ] button to switch to the
sound adjustment selection display.
∗
The factory default sound setting is “ Z-
EHCR ”.
2. Then press the [x] or [v] button to
select the sound adjustment mode.
Each time you press the [x] or [v]
button, the sound adjustment mode
changes as following order:
“ Z-EHCR ” ↔ “ BASS ” ↔ “ TREBLE ” ↔
“ BALANCE ” ↔ “ FADER ”
∗ In the case of display blinking “ ENT ”, you
can press the [ ] button to adjust the
setting value.
3. Press the [w] or [z] button to adjust the
selected audio mode.
4. After completing settings, press the [ ]
button to return to the previous mode.
DXZ378RMP_EN.book 12 ページ ２００６年１１月２７日 月曜日 午後２時２２分