Search
Directory
Brands
Dynojet manuals
Equipment
Scooter Dyno SD-12 Installation Guide
Manual
Dynojet Scooter Dyno SD-12 Installation Guide User Manual
Dynojet Equipment
Text mode
Original mode
Pages:
1
2
3
4
5
6
7
…
44
wrong Brand
wrong Model
non readable
Table of contents
Document Outline
Cover
Copyright
Table of Contents
Warnings
1 - Specifications and Operating Requirements
Introduction
Conventions Used In This Manual
Technical Support
Your Dyno Room
Dynamometer Specifications and Requirements
Chassis Specifications
Compressed Air Requirements
Computer Specifications
Environmental Requirements
Forklift Requirements
Phone and Internet Access
Tie-Down Straps
Dyno Electronics
2 - Installation
Unpacking the Dyno
Unpacking the Dyno
Removing the Drum from the Crate
Installation
Installing the Front Support
Routing Cables
Wiring the Breakout Board
Installing the Ramp
Fold and Move the Dyno
Folding the Dyno
Moving the Dyno
Opening the Dyno
Accessories
Compressed Air Pump Assembly
Stand Alone Blowers
3 - Basic Dyno Operation
Loading the Vehicle
Connecting the RPM Pickup
RPM Pickup Descriptions
Connecting the Secondary Inductive Pickup
Connecting The Primary Inductive Pickup
Pre-Run Inspection
Before Starting the Engine
Engine Warm Up
After Engine Warm Up
Making a Test Run
Preventative Maintenance
Adjusting the Brake
Adjusting the Brake Tension
Index
See also other documents in the category Dynojet Equipment:
150: Kart and ATV Dynamometers
(44 pages)
150: Dyno Drum Cover for Kart and ATV Dyno Motorcycle Option
(3 pages)
150: WinPEP 7
(170 pages)
168: Eddy Current Brake
(27 pages)
200: Eddy Current Brake
(45 pages)
200: Replacing the Starter Ring Gear
(7 pages)
200: Safety Switch
(3 pages)
200: DynoWare EX+ Upgrade Installation Guide for Motorcycle Dynos
(20 pages)
200: Throttle Stop
(3 pages)
200: Eddy Current Brake Driveline Upgrade
(17 pages)
200i: High Pressure Blower
(20 pages)
200: Installation Guide
(73 pages)
200i: Pit Installation Guide
(154 pages)
200i: Pre-Installation Guide
(52 pages)
200i: Installation Guide
(184 pages)
200i: Air Brake and EEC Kit
(40 pages)
200i: Dynamometer Wiring Schematic
(2 pages)
200i: Folding Ramp
(15 pages)
200i: Control Panel Interface Upgrade (S/N 201xxxx)
(31 pages)
200i: Control Panel Interface Upgrade (S/N 202xxxx)
(29 pages)
200i: Motorcycle Exhaust Extraction System Drawings
(18 pages)
200iP: Pit Installation Guide
(148 pages)
200iPX: Installation Guide
(52 pages)
200iPX: Installation Guide
(163 pages)
200ix: Pit Installation Guide
(163 pages)
200ix: Extended Carriage and Trike Adapter Assembly
(15 pages)
200iX: Upgrade Installation Guide
(56 pages)
200ix: Extended Carriage with Trike Adapter Assembly
(13 pages)
224: CE Package
(17 pages)
224: Maintenance Guide
(35 pages)
224: Installation Guide
(78 pages)
224/4WD: Installation Guide
(77 pages)
224: Pit Installation Guide
(56 pages)
224x: Above Ground Four Post Lift Dimensions
(1 page)
224x: Pre-Installation Guide
(63 pages)
224x: 4WD Dyno Air and Wiring Schematic
(2 pages)
224: Eddy Current Brake
(73 pages)
224: Pit Eddy Current Brake
(69 pages)
224xLC2: Quickstart guide for DWRT
(2 pages)
248: Pit Installation Guide
(74 pages)
248: Installation Guide
(58 pages)
248: DynoTRAC User Guide with Variable Brake
(14 pages)
248: DynoWare EX+ Upgrade
(22 pages)
248: Optical RPM Sensor
(22 pages)
248: Proportional Air Brake
(21 pages)
