Code 3 MC SuperVisor Ford PI Sedan - Manual (Page 3)

3
Installation and Mounting Instructions
Step 1
Using a thin flat blade screwdriver, remove the plastic covers from the vehicle's driver and passenger outer sun visor pivot
brackets (see Figures 1 & 2). The trick is to pry the (2) cover retention keepers on either side of the split in the cover out and away
from the pivot bracket to release the cover from the bracket (See the keepers at the top center of the picture of the cover in Figure 2).
Remove the (2) small Torx screws from each of the vehicle's visor pivot brackets as shown in Figure 3. Pull the visor pivot brackets
down from the headliner and very carefully allow the sun visors to hang by the vehicle's attached vanity mirror light wires if so equiped.
Step 2
Remove the single Torx screw that holds each of the vehicle's inner visor clips in place (See Figure 4).
Step 3 Attach the plastic inner visor clips to the SuperVisor Inner Mounting Brackets (See Figure 5) and position them up to the head-
liner as shown in Figure 6. Thread the supplied #8 X 1" Phillips Truss Head Black Oxide Screw up through each of the inner visor clips
and into the mounting holes in the vehicle's headliner. Leave the screws slightly loose.
Step 4 Attach the plastic outer visor pivot brackets to the supplied SuperVisor Outer Mounting Brackets noting the difference between
the passenger and driver side and screw the (2) Torx screws in each bracket as shown in Figure 7 on page 4 (Note the Drivers side is
shown). Tighten the screws to bring the brackets just up against the headliner but do not fully tighten the screws at this time.
Step 5 Route the SuperVisor's cable to the desired side of the vehicle and through the cable clearance slot at the end of the SuperVi-
sor's Outer Panel. Make sure the cable will not interfere with the vehicle's headliner and windshield as you position the SuperVisor up
to the headliner in front of the SuperVisor Mounting Brackets as shown in Figure 8 page 4.
Step 6 Line up the slots in the SuperVisor Inner Mounting Brackets with the threaded holes in the SuperVisor, and thread the sup-
plied 1/4"-20 screws and internal tooth lock washers through the slots and into the SuperVisor's Outer Panel (see Figure 9 page 4).
Step 7 Line up the slots in the SuperVisor Outer Mounting Brackets and thread the supplied 1/4"-20 screws and internal tooth lock
washers through the slot in the SuperVisor's Outer Mounting Brackets and into the SuperVisor's Outer Panel (see Figure 10 page 4).
Step 8 Center up the SuperVisor in the vehicle and tighten each of the two small Torx screws in the SuperVisor's Inner Mounting
Brackets as shown in Figure 11 page 4, then tighten the (2) Torx screws in each of the SuperVisor Outer Mounting Brackets as shown
in Figure 12 on page 4.
Step 9 While pushing the SuperVisor very tightly up against the headliner, tighten the (2) 1/4"-20 SuperVisor Inner Mounting Bracket
screws as shown in Figure 13, then again while pushing the SuperVisor very tightly up against the headliner, tighten the (2) 1/4"-20
SuperVisor Outer Mounting Bracket screws as shown in Figure 14 page 4. Note: It is best to have an assistant push up on the
SuperVisor while you tighten each of the 1/4"-20 screws to assure that it is tight against the vehicle's headliner.
Step 10 Replace the vehicle's driver and passenger outer sun visor pivot bracket covers (see Figure 15 page 4).
FIgURE 1 FIgURE 2 FIgURE 3
FIgURE 4 FIgURE 5 FIgURE 6