Two Brothers Racing Yamaha FZ-6 - Manual

Two Brothers Racing
Juice Box™ - Fuel Controller
2004-08 Yamaha FZ-6 Installation & Operation Manual
Part # 008-117
Parts Incuded
Installation Instructions
Qty. Description Part Number
1 Juice Box™ Fuel Control Kit 008-117
3 Zip Ties
1 Adhesive Velcro Square
V.A.L.E.
V a r i a b l e a x i s l o c k i n g e x h a u s t
TM
Route the Juice Box harness from the left side, rear of the
tank toward the white sub harness connector along the
bikes stock wiring loom, secure with ties.
Disconnect the white connector and plug the Juice Box in
between. (Fig 5)
The Juice Box ground lug will go to one of the crankcase
breather bolts (Fig 6).
Place the Juice Box under the seat in the area behind the
tool kit (Fig 7).
Start the bike. The green LED should scroll left to right and
back for about 3-5 seconds and then go to 1-2 steady or
slowly flashing green LED’s. If the number 1 green LED
and number 8 red LED’s continue flashing after startup
or idling, an injector wiring error is indicated. Re-check
the wires from the JUICE BOX™ and make sure they are
connected to the proper wire of your bike’s stock harness.
MAKE SURE you have the correct wires selected in
the stock harness. DO NOT PROCEED UNLESS ABOVE
CONDITIONS ARE MET.
Bike reassembly is opposite of disassembly.
NOTE: Re check your wire routing and JUICE BOX™
location and make certain that in no way the wires can
come into contact with any moving parts or high heat
source and that the JUICE BOX™ is mounted in a way as
to not cause a handling problem with the machine.
7.
8.
9.
10.
11.
12.
13.
IMPORTANT - PLEASE READ CAREFULLY
Warranty
two brothers racing warrants that this product carries a warranty for 2 years from date of purchase against original
defects in materials and workmanship. should this product fail to perform for either of the above reasons, two brothers
racing will repair or replace it with an equivalent product at no charge, except for postage, to the original retail purchaser.
to obtain the benefits of this warranty, the retail purchaser must return the product and proof of purchase to the place of
original purchase.
We recommend that this performance part be installed by a qualified motorcycle
technician. If you have any doubts as to your ability to install this performance part,
please consult with your local motorcycle dealer. Read all instructions first before
starting installation. Make sure the vehicle and exhaust system are completely cool
before starting the installation. Also, make sure the vehicle is secure during installation.
Be sure to save all stock components for possible use later.
The Juice Box™ is legal ONLY for closed course race vehicles. The Juice Box™ is not
applicable, nor inteded for use on EMISSIONS CONTROLLED street, highway or off-road
vehicles. The Juice Box™ is not applicable, nor inteded for use on aircraft.
Thank you for purchasing a genuine Two Brothers Racing
JUICE BOX™. This product represents a radical step
forward in tuning fuel-injected motorcycles and ATVs for
optimal performance using “load-based” technology.
We at Two Brothers Racing hope that you will find this
development as exciting and useful as we do. And
remember: Proper Fuel = Maximum Power!
Make sure the vehicle is completely cool before starting
the installation. Also, make sure the vehicle is secure and
will not roll around.
Start by removing rear seat.
Remove the two Allen bolts on the left side (Fig 1) that
hold the inside fairing pieces.
And remove fairing section (Fig 2). Perform on right hand
side also.
Remove the two front gas tank mounting bolts (Fig 3).
Gently raise the gas tank up and support with suitable
prop rod.
Locate the white injector sub harness connector (Fig 4).
1.
2.
3.
4.
5.
6.
Tools Needed For Install
- Prop rod to hold gas tank
- 4-5mm Allen Wrench
Continued on page 2
Fig 1
Fig 5
Fig 2
Fig 3
Fig 4
Fig 6
Fig 7