Clarion DXZ946MP - Manual (Page 21)

DXZ946MP
21
English
AC-Processor III Operations
P.EQ basic menu
6. Press the [SOUND] button to return to the
original mode.
Adjusting/storing P.EQ (user
memory)
With user memory, you can compensate the
frequency characteristics to suit your car based
upon the P.EQ basic menu. Up to 6 adjustment
setups can be stored to user memory. For
details, see “P.EQ adjustment”.
1. Press the [SOUND] button.
2. Touch P.EQ.
3. Touch on the ON/OFF display.
The P.EQ effect is toggled ON/OFF.
4. Touch B/U to select “BASIC” or “USER”.
5. Touch on the right of the display to
select the menu that is used as the menu for
adjustment.
6. Press the [A] button.
7. Touch on the left of the display to
select “FRONT” or “REAR”.
RTN
P.EQ EDIT
BAND
FRONT
1
8. Touch on the center of the display to
select each adjustment item.
Each touch of
switches the
adjustment item as follows:
Adjustment items
BAND
➜ FREQ ➜ Q ➜ GAIN ➜ BAND...
9. Touch on the right of the display and
adjust the item as desired.
∗
“BAND” can be adjusted within the range
1 to 3.
∗
“FREQ” can be adjusted within the range
20Hz to 20kHz.
∗
Select one of 1, 3, 5, 7, or 20 as “Q”.
∗
“GAIN” can be adjusted within the range
-12dB to +12dB.
10. Repeat steps 7 to 9 to adjust the desired
item.
11. When you have finished adjusting each item,
touch RTN.
The display returns to the original screen,
and “
” is displayed at the BASIC or USER
display.
Operation so far completes P.EQ
adjustment. To continue to store the
adjustment values to the P.EQ user menu,
perform the following.
12. Touch and hold RTN for 1 second or longer.
The P.EQ menu list is displayed.
13. Touch and hold the user memory you want
to store the adjustment values to for 2
seconds or longer.
You will hear a long beep, and the values
you adjusted up to step 10 are stored to the
P.EQ menu.
If you hear a short beep, the adjustment
values up to step 10 are discarded. Adjust
these values again as required.
14. Touch RTN.
15. Press the [SOUND] button to return to the
original mode.
∗
To select a stored user memory, touch B/U
to display “USER” and touch on the
user memory No.
■ P.EQ adjustment
The settings that can be adjusted in the P.EQ
menu are as follows. The center frequency, gain
and Q curve can be stored to channel/band
combinations.
For example, center frequency “250Hz”, gain “
-8dB” and Q curve “3” can be stored to band 1
on the front.
FRONT/REAR (channel selection)
Selects the channel (front or rear) to adjust.
BAND (band selection)
Selects the frequency band (1 to 3) to adjust.
Set the center frequency (FREQUENCY), gain
(GAIN) and Q curve (Q) for each frequency
band.
No. Display name
Speaker Mounting
position
1 SEDAN-1 Front: Front door
Rear: Rear parcel
2 SEDAN-2 Front: Front door
Rear: Rear door
3 WAGON-1 Front: Front door
Rear: Luggage (side)
4 WAGON-2 Front: Front door
Rear: Rear door
5 MINI VAN-1 Front: Front door
Rear: Luggage (side)
6 MINI VAN-2 Front: Front door
Rear: Rear door