Great Plains ADC2250 Operator Manual - Manual (Page 38)

36
Section 3 Adjustments
Model 2250 Air Drill Cart 167-033M 7/28/10
Great Plains Mfg., Inc.
Fertilizer Rate Chart
60 Lbs/Cu Ft
Seed
Rate
Quick Change
Sprocket
(See Figure 3-6)
Driving/Driven Gears
(See Figure 3-1)
Gearbox
Shift
Levers
(See
Figure 3-3)
Seed
Rate
Quick Change
Sprocket
(See Figure 3-6)
Driving/Driven Gears
(See Figure 3-1)
Gearbox
Shift
Levers
(See
Figure 3-3)
Lbs/Acre Driving 1 Driven 2 Driving 3 Driven 4 Lbs/Acre Driving 1 Driven 2 Driving 3 Driven 4
2.1 20 30 17 54 E5 29.4 20 30 54 17 E5
2.5 20 30 17 54 D5 33.6 20 30 54 17 D5
2.9 20 30 17 54 E4 36.7 20 30 54 17 E4
3.1 20 30 17 54 C5 39.1 20 30 54 17 C5
3.4 20 30 17 54 D4 41.8 20 30 54 17 D4
3.6 20 30 17 54 E3 43.8 20 30 54 17 E3
4.0 20 30 17 54 B5 46.7 20 30 54 17 B5
4.2 20 30 17 54 C4 48.6 20 30 54 17 C4
4.3 20 30 17 54 D3 49.9 20 30 54 17 D3
4.4 20 30 17 54 E2 50.9 20 30 54 17 E2
5.2 20 30 17 54 E1 57.8 20 30 54 17 E1
5.2 20 30 17 54 D2 57.8 20 30 54 17 D2
5.2 20 30 17 54 C3 57.8 20 30 54 17 C3
5.2 20 30 17 54 B4 57.8 20 30 54 17 B4
5.2 20 30 17 54 A5 57.8 20 30 54 17 A5
6.1 20 30 17 54 D1 65.6 20 30 54 17 D1
6.2 20 30 17 54 C2 66.9 20 30 54 17 C2
6.4 20 30 17 54 B3 68.7 20 30 54 17 B3
6.7 20 30 17 54 A4 71.4 20 30 54 17 A4
7.2 20 30 17 54 C1 75.8 20 30 54 17 C1
7.6 20 30 17 54 B2 79.3 20 30 54 17 B2
8.3 20 30 17 54 A3 84.5 20 30 54 17 A3
8.9 20 30 17 54 B1 89.6 20 30 54 17 B1
9.8 20 30 17 54 A2 97.3 20 30 54 17 A2
11.3 20 30 17 54 A1 109.7 20 30 54 17 A1
6.0 30 20 17 54 E5 64.6 30 20 54 17 E5
6.9 30 20 17 54 D5 73.2 30 20 54 17 D5
7.7 30 20 17 54 E4 79.6 30 20 54 17 E4
8.3 30 20 17 54 C5 84.5 30 20 54 17 C5
8.9 30 20 17 54 D4 90.0 30 20 54 17 D4
9.4 30 20 17 54 E3 94.1 30 20 54 17 E3
10.1 30 20 17 54 B5 99.8 30 20 54 17 B5
10.5 30 20 17 54 C4 103.5 30 20 54 17 C4
10.9 30 20 17 54 D3 106.2 30 20 54 17 D3
11.1 30 20 17 54 E2 108.2 30 20 54 17 E2
12.8 30 20 17 54 E1 121.8 30 20 54 17 E1
12.8 30 20 17 54 D2 121.8 30 20 54 17 D2
12.8 30 20 17 54 C3 121.8 30 20 54 17 C3
12.8 30 20 17 54 B4 121.8 30 20 54 17 B4
12.8 30 20 17 54 A5 121.8 30 20 54 17 A5
14.8 30 20 17 54 D1 137.1 30 20 54 17 D1
15.1 30 20 17 54 C2 139.6 30 20 54 17 C2
15.5 30 20 17 54 B3 143.0 30 20 54 17 B3
16.2 30 20 17 54 A4 148.2 30 20 54 17 A4
17.3 30 20 17 54 C1 156.8 30 20 54 17 C1
18.2 30 20 17 54 B2 163.6 30 20 54 17 B2
19.6 30 20 17 54 A3 173.7 30 20 54 17 A3
20.9 30 20 17 54 B1 183.7 30 20 54 17 B1
22.9 30 20 17 54 A2 198.6 30 20 54 17 A2
26.2 30 20 17 54 A1 223.4 30 20 54 17 A1
1 Connected to the gearbox output shaft. 2 Connected to the meter input shaft. 3 Located on the front/upper shaft of the meterbox. 4 Located on the lower/back shaft of the meterbox