Great Plains ADC2250 Operator Manual - Manual (Page 36)

34
Section 3 Adjustments
Model 2250 Air Drill Cart 167-033M 7/28/10
Great Plains Mfg., Inc.
Durum Seed Rate Chart
Plenty Variety - 61 ;bs/bu
Seed
Rate
Quick Change
Sprocket
(See Figure 3-6)
Driving/Driven Gears
(See Figure 3-1)
Gearbox
Shift
Levers
(See
Figure 3-3)
Seed
Rate
Quick Change
Sprocket
(See Figure 3-6)
Driving/Driven Gears
(See Figure 3-1)
Gearbox
Shift
Levers
(See
Figure 3-3)
Lbs/Acre Driving 1 Driven 2 Driving 3 Driven 4 Lbs/Acre Driving 1 Driven 2 Driving 3 Driven 4
1.9 20 30 17 54 E5 27.2 20 30 54 17 E5
2.3 20 30 17 54 D5 31.1 20 30 54 17 D5
2.6 20 30 17 54 E4 34.0 20 30 54 17 E4
2.9 20 30 17 54 C5 36.2 20 30 54 17 C5
3.1 20 30 17 54 D4 38.8 20 30 54 17 D4
3.3 20 30 17 54 E3 40.7 20 30 54 17 E3
3.6 20 30 17 54 B5 43.4 20 30 54 17 B5
3.8 20 30 17 54 C4 45.1 20 30 54 17 C4
3.9 20 30 17 54 D3 46.4 20 30 54 17 D3
4.0 20 30 17 54 E2 47.4 20 30 54 17 E2
4.7 20 30 17 54 E1 53.9 20 30 54 17 E1
4.7 20 30 17 54 D2 53.9 20 30 54 17 D2
4.7 20 30 17 54 C3 53.9 20 30 54 17 C3
4.7 20 30 17 54 B4 53.9 20 30 54 17 B4
4.7 20 30 17 54 A5 53.9 20 30 54 17 A5
5.6 20 30 17 54 D1 61.4 20 30 54 17 D1
5.7 20 30 17 54 C2 62.6 20 30 54 17 C2
5.9 20 30 17 54 B3 64.3 20 30 54 17 B3
6.2 20 30 17 54 A4 66.9 20 30 54 17 A4
6.6 20 30 17 54 C1 71.1 20 30 54 17 C1
7.0 20 30 17 54 B2 74.5 20 30 54 17 B2
7.6 20 30 17 54 A3 79.5 20 30 54 17 A3
8.1 20 30 17 54 B1 84.5 20 30 54 17 B1
9.0 20 30 17 54 A2 91.8 20 30 54 17 A2
10.4 20 30 17 54 A1 103.9 20 30 54 17 A1
5.5 30 20 17 54 E5 60.4 30 20 54 17 E5
6.4 30 20 17 54 D5 68.7 30 20 54 17 D5
7.0 30 20 17 54 E4 74.8 30 20 54 17 E4
7.6 30 20 17 54 C5 79.5 30 20 54 17 C5
8.2 30 20 17 54 D4 84.8 30 20 54 17 D4
8.6 30 20 17 54 E3 88.8 30 20 54 17 E3
9.3 30 20 17 54 B5 94.3 30 20 54 17 B5
9.7 30 20 17 54 C4 97.9 30 20 54 17 C4
10.0 30 20 17 54 D3 100.5 30 20 54 17 D3
10.2 30 20 17 54 E2 102.4 30 20 54 17 E2
11.8 30 20 17 54 E1 115.8 30 20 54 17 E1
11.8 30 20 17 54 D2 115.8 30 20 54 17 D2
11.8 30 20 17 54 C3 115.8 30 20 54 17 C3
11.8 30 20 17 54 B4 115.8 30 20 54 17 B4
11.8 30 20 17 54 A5 115.8 30 20 54 17 A5
13.6 30 20 17 54 D1 130.7 30 20 54 17 D1
13.9 30 20 17 54 C2 133.2 30 20 54 17 C2
14.3 30 20 17 54 B3 136.6 30 20 54 17 B3
14.9 30 20 17 54 A4 141.7 30 20 54 17 A4
15.9 30 20 17 54 C1 150.1 30 20 54 17 C1
16.8 30 20 17 54 B2 156.7 30 20 54 17 B2
18.0 30 20 17 54 A3 166.6 30 20 54 17 A3
19.3 30 20 17 54 B1 176.3 30 20 54 17 B1
21.1 30 20 17 54 A2 190.6 30 20 54 17 A2
24.2 30 20 17 54 A1 214.1 30 20 54 17 A1
1 Connected to the gearbox output shaft. 2 Connected to the meter input shaft. 3 Located on the front/upper shaft of the meterbox. 4 Located on the lower/back shaft of the meterbox